Saw video thread

[huskihl]

Very cool Mr. K. What's your impression so far? It seems it has pretty good snort initially.

Pretty much a 572 on steroids. It’s different than the 390 and 395. I think it will do OK with any normal length bar

 

[huskihl]

Close as I can get for a comparo. Rebuilt stock 390. New bearings, new oem 390 p/c.

*Edit
Once I opened it up, exhaust and intake had been widened slightly exhaust raised a little bit, base gasket delete, and a timing advance. It was probably worth a few seconds in this log

 

[huskihl]

Stock 592 about 31 seconds
Ported 7310 about 38
Stock 390 about 36

 

[JT78]

Stock 592 about 31 seconds
Ported 7310 about 38
Stock 390 about 36

Plans to port these and then compare again?

 

[huskihl]

Plans to port these and then compare again?

The 7310 already is.

And yep on the 390 and 592. I’ll actually be done with the 390 tomorrow

 

[huskihl]

I edited my post above about the stock 390. Once I pulled it apart for porting, I noticed the exhaust and intake had been widened slightly, timing advanced, and gasket deleted. All that was probably worth a few seconds in this log.

Here’s the ported video after I was done with it

 

[RI Chevy]

Nice job. Got a bit more angry!

 

[Slumberjack]

My ported husky 372xp 24” 8t. Like it with that setup.

 

[Red97]

New shop channel is up.

Will be posting dyno vids, saw builds, and clips of my other shop jobs and such.

 

[davidwyby]

I was checking out my stock 3120 in preparation to sell it and had never cut with it. Only large mount bar I had handy was 20” and some aggressive round filed…what the heck. All I had for wood is the little 9” stuff I keep at home for testing. It was fun! Can’t stop it. So I decided to finally put the play bar and chain along with the 12 pin on the ported 3120. First time with the big saw and a rickety setup but here we go. A least it’s not slow dry hard eucalyptus. It’s dry athel pine….

I cut off the vid because it all went to heck when I tried to up cut, ha! Need to build a better log stand or just do it at the shop…I’m sure my neighbors don’t appreciate it.

 

[Red97]

What's the channel name Joe? For some reason I can only play the vid. Can't share it with myself or watch later. Can't open it in YouTube.

https://youtube.com/channel/UCAMrRtDJGU80JhYtxOkaMFw

 

[Red97]

Should be good for a chuckle, or a 3pm Friday headache.

First attempt at any editing.

Good luck

 

[jacob j.]

Should be good for a chuckle, or a 3pm Friday headache.

First attempt at any editing.

Good luck

Geeze Joe, that's about the ugliest bench I've seen. If it were covered in Macs, it would look a lot better...

 

[Red97]

Geeze Joe, that's about the ugliest bench I've seen. If it were covered in Macs, it would look a lot better...

I'm not sure if it will handle all that power...

You might have to send a few 6 cubes down and test it out.

 

[jacob j.]

I'm not sure if it will handle all that power...

You might have to send a few 6 cubes down and test it out.

That's still the plan. I still have two saws I need to finish up for members here (who've been waiting quite a while) and get a few projects knocked out
at my day job before I can make it happen.

 

[davidwyby]

 

[RI Chevy]

Ooof. Painful...lol

 

[Red97]

Pretty much all of these builds are on here, let me know how you like my attempt at a video "build thread"

 

[Catman]

Pretty much all of these builds are on here, let me know how you like my attempt at a video "build thread"

Love the Time and Effort you put into these Experimental Builds! Some Nice Running Saws Brother!!

 

[Red97]

Love the Time and Effort you put into these Experimental Builds! Some Nice Running Saws Brother!!

Thank you

Now I'm just trying to figure out this editing stuff.

The vids should get better as I go.