monkeyed up 2188

[mdavlee]

You'll be more than happy with it "Jack", I sure like my 2186 Scott did, don't matter if it's got the 24" or 30" bar and I run 8 pin rim all the time


Sent from my iPhone using Tapatalk

Last one I ported we ran it with a 34 and 36" with an 8 pin. Even cut through a nail or something with it on the 36".

 

[czar800]

Hopefully some day I get to run one of your saw. Need to find some gtg this year. Nice work!

 

[MG2186]

Last one I ported we ran it with a 34 and 36" with an 8 pin. Even cut through a nail or something with it on the 36".

That's quite a chain to cut through a nail


Sent from my iPhone using Tapatalk

 

[Duane(Pa)]

That's quite a chain to cut through a nail


Sent from my iPhone using Tapatalk

Hold my beer (dew) an' watch this...gonna' cut through this nail....Really Fast

 

[mdavlee]

That's quite a chain to cut through a nail


Sent from my iPhone using Tapatalk

We noticed it slowed down a little near the bottom of the log. When it rolled free we seen a blue spot.

 

[MG2186]

We noticed it slowed down a little near the bottom of the log. When it rolled free we seen a blue spot.

Always hate that hidden hardware in the middle of a log!


Sent from my iPhone using Tapatalk

 

[mdavlee]

It wasn't my chain but at least he has a grinder to fix it.

 

[Duane(Pa)]

Scott, thanks for doing this thread. Bright spot in a dark winter for me.

 

[Redfin]

Thanks for putting this up Scott. Do you do much work to the lower trans where it enters the jug? Is this jug similar to the 2186?

 

[David Young]

Nice build Scott thank you!

Do you advance the timing?
do you open all solid pistons up or just some. What does it do and how do you make it work

how many Dews does it take to do a 2188?

David

 

[jmssaws]

I cut a nail with a 36" and it stopped the cutting immediately.

 

[David Young]

I cut a nail with a 36" and it stopped the cutting immediately.

sounds like you need a Jonsered

 

[mdavlee]

I cut a nail with a 36" and it stopped the cutting immediately.

Need to ask Keith if he still has those photos.

 

[04ultra]

You'll be more than happy with it "Jack", I sure like my 2186 Scott did, don't matter if it's got the 24" or 30" bar and I run 8 pin rim all the time


Sent from my iPhone using Tapatalk

Mike I wont see this saw again till trade in time ....Its heading for southern IL.

 

[jmssaws]

sounds like you need a Jonsered

Whats a johnsred?

 

[jmssaws]

I don't think it was the saws fault,I'm thinking it's the chain.

 

[MG2186]

Mike I wont see this saw again till trade in time ....Its heading for southern IL.

Dam you won't even to get to make a couple test cuts to enjoy it a little, your customer will be more than happy!


Sent from my iPhone using Tapatalk

 

[Redfin]

Whats a johnsredfin?

Thats me silly

 

[Mastermind]

I'm telling you guys. This porting thing is just a silly fad.

Mark my words, by the year 2200 no one here will be still running a ported saw.

 

[Sty57]

I'm telling you guys. This porting thing is just a silly fad.

Mark my words, by the year 2200 no one here will be still running a ported saw.

Will you be porting lightsabers by then?