Huskyboy meets the 572xp

[Stump Shot]

Thanks for getting ne straight on the Hooskie chain nomenclature Mason and Dominick. Lol
Have you tried to file it yet Mason?

It's spelled "Husqvarna" there Mr. Hot Hands. Lol

 

[huskyboy]

Thanks for getting ne straight on the Hooskie chain nomenclature Mason and Dominick. Lol
Have you tried to file it yet Mason?

Just touched it up two swipes or so.

 

[old guy]

I've filed the c83, it seems hard but not too hard. It is smooth cuttin chain.

 

[huskyboy]

I've filed the c83, it seems hard but not too hard. It is smooth cuttin chain.

I agree with that.

 

[hseII]

It's spelled "Husqvarna" there Mr. Hot Hands. Lol

Tell me about them after they’ve been worked for 6 months in the Heat there SupaMod.


Sent from my iPhone using Tapatalk Pro

 

[Stump Shot]

Tell me about them after they’ve been worked for 6 months in the Heat there SupaMod.


Sent from my iPhone using Tapatalk Pro

I think he only has the one, so he can switch off if it gets too hot I would suppose and am just a junior mod.

 

[concretegrazer]

I like it too, but c85 might be faster. Haven’t compared them directly yet.

Thanks. Good to know ahead it'll be disappointing.

 

[hseII]

I think he only has the one, so he can switch off if it gets too hot I would suppose and am just a junior mod.

You’re Doing Great Steve.


Sent from my iPhone using Tapatalk Pro

 

[Skeans1]

I like it too, but c85 might be faster. Haven’t compared them directly yet.

How does it compare to square?


Sent from my iPhone using Tapatalk

 

[huskyboy]

How does it compare to square?


Sent from my iPhone using Tapatalk

I can’t comment on that sir, don’t really run square myself. It probably it wouldn't be faster, but it seemed to hold up well as far as staying sharp.

 

[MustangMike]

How come I did not get to run a 572 at the GTG??? My 462 was there!!!

 

[RI Chevy]

I think your 462 just edged out the 572 in the cant cut.

 

[huskyboy]

I think your 462 just edged out the 572 in the cant cut.

Incorrect. I got a 14.5 and 15 seconds cut. Mark’s 462 or Mike’s (not sure who’s it was)... got a 15.5 I believe. 572 was on its first tank and running stock round chain. It’s pretty pointless to compare not using the same bar and chain however.

 

[Skeans1]

I can’t comment on that sir, don’t really run square myself. It probably it wouldn't be faster, but it seemed to hold up well as far as staying sharp.

Pm sent


Sent from my iPhone using Tapatalk

 

[RI Chevy]

Incorrect. I got a 14.5 and 15 seconds cut. Mark’s 462 or Mike’s (not sure who’s it was)... got a 15.5 I believe. 572 was on its first tank and running stock round chain. It’s pretty pointless to compare not using the same bar and chain however.

Simmer down now... I was standing next to Mark when he timed one of the cuts. 462 ran a 14.5...
But you are correct with keeping the variables in check.

 

[MustangMike]

Mine was running a slight bit faster than Mark's due to the muffler mod. He also said it felt a little "snappier".

Not bad times at all for a basically stock saw … that White Oak cant was tough stuff!

What were the 7900 times?

 

[RI Chevy]

Mason's 7900 was pretty fast. All within that 13 to 14 second range. His may have been that 13.3 time.
He has done most everything to the saw short of porting it. So it isn't stock...

 

[huskyboy]

Get your times right guys...
Jeff 14.28
Brett 13.51
Mike 12.4
D dave 13.58
Dave f 12.98
Mason 13.2/13.36
Mike cfb 11.18
Cobby 462 15.16
572 15.10
Gernade 10.66
Dave 310 11.91
Brett 11.51
El freako 12.0
Dave stroker 10.76

 

[RI Chevy]

YUP. Your missing my 660 10.3 second cut there bud...

Plus Cobby had a few pops in him from the night before. LOL

 

[huskyboy]

Let us also remember that the 462 and 572 were stock saws and the 572 running stock out of the box round chain. They were running against highly modded saws, pretty impressive how the times weren’t that far behind. These new 70cc saws aren’t slouches.