how about a Oklahoma,AR,MO,KS,TX,+IA GTG thread?

[moparnut88]

Yea they are calling for record lows here by Thursday. Double checking to make sure we’re ready for that cold a temps.


Sent from my iPhone using Tapatalk

 

[Bryan Newton]

Morning yall

Staywarm and safe o ut there getting ready for the weather later this week

 

[BrettL]

Good morning y'all. I need to remove the clutch on my 200t. I hate to put anything in the cylinder but I need some kind of piston stop. I've used rope on model engines. What do you think?

 

[Hedgerow]

Looked at the forecastn for this week and decided I am burning the good white oak this week. Boiler over shoots the set point by 4 degrees each burn. Burns hot! Blizzard Thursday! 10 inches and 47 mph wind gusts

I wish minnesnowduh would close the door and keep all that *s-word up der eh?

 

[Hedgerow]

Good morning y'all. I need to remove the clutch on my 200t. I hate to put anything in the cylinder but I need some kind of piston stop. I've used rope on model engines. What do you think?

I just use an electric impact. No piston stop.

 

[BrettL]

I just use an electric impact. No piston stop.

I wish I had an electric impact. I'm going to have to do it by hand.

 

[Semotony]

It's supposed to be -3° here by Thursday night.

I like winter fine.... but, below about 15° is kinda extravagant imo.....

Windchill at boot camp ran between a¿ high? of -60° to a low of -69° when I bothered to pay attention to weather channel on drill instructors radio. Thotful guy he was

 

[Bryan Newton]

Good morning y'all. I need to remove the clutch on my 200t. I hate to put anything in the cylinder but I need some kind of piston stop. I've used rope on model engines. What do you think?

I Use rope or leave spark plug in and use a impact driver

 

[Bryan Newton]

I wish I had an electric impact. I'm going to have to do it by hand.

A 1/4 inch impact works too

 

[hoskvarna]

Good morning y'all. I need to remove the clutch on my 200t. I hate to put anything in the cylinder but I need some kind of piston stop. I've used rope on model engines. What do you think?

I still use it [emoji106]


Sent from Hoskey Hills

 

[Sawdust Man]

Afternoon everybody.

Any of y'all burn blackjack oak in the woodstove? how does it compare to something like hickory or post oak?

 

[Bryan Newton]

Afternoon everybody.



Any of y'all burn blackjack oak in the woodstove? how does it compare to something like hickory or post oak?

When I was a young kid my parents burnt it but thats about all I can remember

 

[Hedgerow]

Afternoon everybody.

Any of y'all burn blackjack oak in the woodstove? how does it compare to something like hickory or post oak?

It’s an oak... just really wet when cut.. so takes some time to dry out and make proper heat.

 

[Sawdust Man]

It’s an oak... just really wet when cut.. so takes some time to dry out and make proper heat.

It stinks.

It's totally worthless for lumber, so I've just been making firewood outta it.

 

[Cat 525]

Wind and snow forecast not liking at all!

 

[Hedgerow]

It stinks.

It's totally worthless for lumber, so I've just been making firewood outta it.

Yeah, it’s some sour *s-word..
But split it up and let it dry a couple years, and it’ll burn fine.
If you burn it at less than a year, it’ll still sizzle out the ends.

 

[Hedgerow]

Wind and snow forecast not liking at all!

What they calling for out on your end?

 

[Cat 525]

What they calling for out on your end?

3 to6 of snow but 50mph winds! Probably be busting drifts Friday!

 

[Hedgerow]

3 to6 of snow but 50mph winds! Probably be busting drifts Friday!

With 50 mph winds, you may never get to see any of that snow. It will just keep blowing all the way to Kansas City.

 

[Hedgerow]

Wayne left the damn door open again..