how about a Oklahoma,AR,MO,KS,TX,+IA GTG thread?

[moparnut88]

Had a real good time playing with saws with @Semotony gonna cut those loads up tomorrow. I'll try to post several pics for you guys!

Sent from my SM-N950U using Tapatalk

 

[67L36Driver]

First assembly snag on the Farmertec 200.

Sprocket locks down when you run on the clutch. Length thru bore is .513”. OEM sample here is .509”.

Soooooo close! [emoji90]

 

[Dub11]

Nope that's our personal company color 1970 Chrysler big bad green.

Sent from my SM-N950U using Tapatalk

It's a good color.

 

[Locust Cutter]

First load of about 3 getting ready to cut up tomorrow and split.

Sent from my SM-N950U using Tapatalk

That's about what I have in mind for a GN trailer, though I like the option where the Dove tail is two half-width flip-over ramps. How does the ramp system work on that thing? I DO love the color!!!!

 

[Dub11]

This foggy out this AM.

 

[Semotony]

After spending a couple hours driving to and from, spending more time on my feet (about 5hours) than is typical. Unloading the van for the auction today,,sleep was easy in 40° weather overnight. Hope there is not much for me at this auction. Gotta load up some Older Craftsman, Keen Kutter and other items for the swap & sell tool meet tomorrow at the woodworking supply store St Louis

 

[WKEND LUMBERJAK]

This foggy out this AM.
View attachment 145376

I hope that is just fog

 

[Dub11]

I hope that is just fog

Yes it is.

But the low hanging smoke from the beer drinking fires looked about the same last night.

 

[67L36Driver]

Morning midlanders!

Fog sucks on a long commute.

I was fortunate that I was eight minutes from work. Kitchen door to office door!

Car barely warmed up.

 

[rsting]

Morning everybody

 

[Dustin]

Morning all

Sent from my SM-G935T using Tapatalk

 

[Dub11]

Fogs still here

 

[moparnut88]

That's about what I have in mind for a GN trailer, though I like the option where the Dove tail is two half-width flip-over ramps. How does the ramp system work on that thing? I DO love the color!!!!

It's a fully hydraulic trailer including the Jack's the deck on the dove raises up and the small section flips out then the let down to make a really long dove. I'll try to open it today and send you a pic. We built it from scratch.

Sent from my SM-N950U using Tapatalk

 

[moparnut88]

Here a few for a start this morning. Making good progress.

Sent from my SM-N950U using Tapatalk

 

[sawnami]

Good morning.

Scratcher chains are so simple to file. [emoji849] Cuts a 3/8" kerf.

Sent from my SM-N950U using Tapatalk

 

[67L36Driver]

But, but, there is sooooo many of them. [emoji15]

 

[Dub11]

It's a fully hydraulic trailer including the Jack's the deck on the dove raises up and the small section flips out then the let down to make a really long dove. I'll try to open it today and send you a pic. We built it from scratch.

Sent from my SM-N950U using Tapatalk

Yeah we gonna need video please.

 

[Semotony]

Morning midlanders, again, maybe. So next to nothing at the auction; 9 years ago was the good tool selection. Now the lady of the house stuff that heirs picked thru so very little. But was in the area of the tracker vehicle & got better selection of pics size perspective x 2 drive link view w rear suspension and for moparnut88 and others involved with this nature of vehicle:
A more direct identifier I hope to value, depending on condition of the undercarriage & drive.
Found a part load at yard waste dump that is dropped off around a couple corners for Travis to split and sell.
A larger Cat brand loader w/thumb at dump so burning the limbs and brush may have been approved by epa

 

[moparnut88]

Well got it all cut up and 7 3/4 rank split up and stacked into racks.

Sent from my SM-N950U using Tapatalk

 

[moparnut88]

I didnt get a video but here it is halfway flipped out. The small section continues to flip out til straight then they both let down for one big ramp.

Sent from my SM-N950U using Tapatalk