Dolmar 133...or 143

[ranchdadmike]

I'm looking at a dolmar 133 as a project. It currently doesn't run and I'm told it doesn't get fuel. I'm mostly a husky guy so I'm asking the storehouse of knowledge that is this site: A) is the 133 a good saw and B) are parts even somewhat available? I think the 133 is an 85cc saw and I've always admired the larger dolmars from afar...just wondering if I should pull the trigger on this one. TIA



Sent from my iPhone using Tapatalk

 

[peter92]

i had one of these and boy have they got torque
Peter

 

[Adirondackstihl]

@cuttinscott

 

[peter92]

I'm looking at a dolmar 133 as a project. It currently doesn't run and I'm told it doesn't get fuel. I'm mostly a husky guy so I'm asking the storehouse of knowledge that is this site: A) is the 133 a good saw and B) are parts even somewhat available? I think the 133 is an 85cc saw and I've always admired the larger dolmars from afar...just wondering if I should pull the trigger on this one. TIA
hope this helps you out
Peter


Sent from my iPhone using Tapatalk

 

[backhoelover]

I'm looking at a dolmar 133 as a project. It currently doesn't run and I'm told it doesn't get fuel. I'm mostly a husky guy so I'm asking the storehouse of knowledge that is this site: A) is the 133 a good saw and B) are parts even somewhat available? I think the 133 is an 85cc saw and I've always admired the larger dolmars from afar...just wondering if I should pull the trigger on this one. TIA



Sent from my iPhone using Tapatalk

check carb parts first.
a very bad leaking crankseal will cause very low crank case impulse causing the carb fuel pump diaphragm not to work (not pulling fuel from the gas tank)

 

[backhoelover]

also rotten fuel line and stop up fuel filter can cause this problem also

 

[166]

Very very few parts available

 

[ranchdadmike]

Any dolmar serial number guys here? I bought what was advertised as a non running 133..but it sure looks like a 143


Sent from my iPhone using Tapatalk

 

[cuttinscott]

Any dolmar serial number guys here? I bought what was advertised as a non running 133..but it sure looks like a 143


Sent from my iPhone using Tapatalk

Looks to be a 1988 +/- Vintage Sachs Dolmar 143mx 95cc depending on condition that saw was monster torque and ran 25"-40"ish bars very well HS Carb was simple. The parts problem is Ignition That model used SEM which is NLA earlier models had Bosch which are also NLA. Best ignition parts sources are used late model demo saws 309 or 343

Scott

 

[hseII]

Looks to be a 1988 +/- Vintage Sachs Dolmar 143mx 95cc depending on condition that saw was monster torque and ran 25"-40"ish bars very well HS Carb was simple. The parts problem is Ignition That model used SEM which is NLA earlier models had Bosch which are also NLA. Best ignition parts sources are used late model demo saws 309 or 343

Scott

Hey Dood.

The 056 SEM repairs mentioned on AS, would that repair be possible with the mentioned Dolly?

Do Youins have a 143mx?

 

[Adirondackstihl]

Hey Dood.

The 056 SEM repairs mentioned on AS, would that repair be possible with the mentioned Dolly?

Do Youins have a 143mx?

75% sure they no hab an MX

 

[Adirondackstihl]

I stand corrected....
They have at least 1
.....

 

[Adirondackstihl]

You surbrised @hseII ?

 

[166]

 

[166]

I stand corrected....
They have at least 1
.....

View attachment 58710

More than one and less than 7.

 

[Adirondackstihl]

More than one and less than 7.

See.....

 

[hseII]

You surbrised @hseII ?

Not in the least.

 

[mdavlee]

Is it worth it to search out a 143 top end for a 133? I'm guessing a 153 top end won't swap over?

 

[ranchdadmike]

So, I'm breaking down the 143..and have this:

.
You guys are way better versed at cylinder viability than I am. Is this one ok? Any of you guys need 143 parts? Piston is shot, muffler is banged up, and it's missing the inner dawg but everything else is there and in pretty good shape. Nice full wrap too..trying to decide to fix, part out, or sell as a whole. Advice and comments welcome


Sent from my iPhone using Tapatalk

 

[RedFir Down]

So, I'm breaking down the 143..and have this:

.
You guys are way better versed at cylinder viability than I am. Is this one ok? Any of you guys need 143 parts? Piston is shot, muffler is banged up, and it's missing the inner dawg but everything else is there and in pretty good shape. Nice full wrap too..trying to decide to fix, part out, or sell as a whole. Advice and comments welcome


Sent from my iPhone using Tapatalk

@Four Paws