Any Chinese chainsaw and chinese parts discussion

[Terry Syd]

I just checked Ebay Australia and they had this carb, with the right number for a 365 carb (503 28 32 03)

http://www.ebay.com.au/itm/Carburet...733908?hash=item41994b76d4:g:0X4AAOSwstxVCVWk

The price is right, but you just don't know what you've got until it's in your hands.

 

[Poleman]

Terry, all the clones and the twin jets looked the same with the chrome choke plate...
I've also seen black and white on both

The one on the left is the type that came with the saw and the one on the right is a twin jet clone. There's no way to tell them apart without taking off the diaphragm plate.
I've corresponded with Farmertec and sent pictures of both and the difference and have explained until I was blue in the face but no results. I suggested even making the twin jet carb and charging more just designate what it is. I'm thinking that's what's driving the carbs we're receiving now is production cost. There are brass jets and more milling involved. My thoughts anyway.

 

[Poleman]

I've tryed them too and there single jet....I haven't received a twin jet carb in over a year.
The last one I found that was modded was the one I put on the 365 at present.

 

[Czed]

Bought six more 20 inch full chisel chains i like it it's holding up fine in all the cutting I've done cuts good.
64.99 for six chains one stihl chain here is 30.60 or so after taxes.
I've just been buying oregon bar and chain combos for a little more

 

[Poleman]

Man that's expensive chain.... (Stihl that is)... I will have to check out local dealer out next time I'm there. I usually run Oregon and get it at a Husky Dealer for a buck an inch... 84DL or 24 for $24 and so on plus my discount makes it slightly less...

 

[Czed]

Stihl oil is on sale but i much prefer red armor 13.88 for it and doesn't give me a headache like stihl and husky oil does.

 

[Czed]

Man that's expensive chain.... (Stihl that is)... I will have to check out local dealer out next time I'm there. I usually run Oregon and get it at a Husky Dealer for a buck an inch... 84DL or 24 for $24 and so on plus my discount makes it slightly less...

They have "dealer day's " at stihl occasionally so that makes it around 45-50 dollars for two chains lol
This is the going rate in the places I've checked around here Oregon's a bit cheaper i like it too
Mostly cut firewood now so i'll stick with the china chain.

 

[Poleman]

Hey if it works, I'd use it too!!! Nothing wrong with saving some money!!!!

 

[Czed]

Cut dead pine today a couple of tanks didn't even change rpm it just rips through lol

 

[Czed]

Seeing more and more saws like the king park identical chassis different plastic this ones like the craftsman 42cc i posted before this ones at a rural king.
I would just buy one off ebay 80.00-100.00 shipped 50-52 or 58cc
The 42cc feels just as heavy as the larger displacement saws.

 

[Adamski]

Are you guys running OEM or Chinese Carbs?

 

[Czed]

Are you guys running OEM or Chinese Carbs?

I'm running what came on my 4 saw's.
I did have to change one spring
Other than that they have been good
And they hold their tune no issue's.

 

[rocco490]

Screw China
Ill stick with Husky Solo/Dolmar and Stihl

nothing against the op have a great summer

 

[Adamski]

I'm running what came on my 4 saw's.
I did have to change one spring
Other than that they have been good
And they hold their tune no issue's.

Yeah I am having serious trouble with my OEM walbro holding it's tune..

 

[Czed]

I've tryed them too and there single jet....I haven't received a twin jet carb in over a year.
The last one I found that was modded was the one I put on the 365 at present.

Since i replaced the fuel and breather lines the carbs been doing good no issue's.
three tanks today.
running the semi chisel setup that came with it cutting dirty wood loggers left.
Found a wasp nest.
Did you get your carb where you wanted it.

 

[Czed]

Yeah I am having serious trouble with my OEM walbro holding it's tune..

If the carb is new check your lines thoroughly for kinks or even splits.
I've had to work on new oem carbs
Kits etc.
When they wouldn't hold tune.

 

[Adamski]

If the carb is new check your lines thoroughly for kinks or even splits.
I've had to work on new oem carbs
Kits etc.
When they wouldn't hold tune.

All new tubes, no split, rebuilt carb. New seals... blah blah.. It as if the low needle moves/vibrates in use..

 

[Czed]

Put three more tank's through it ripping down dirty seasoned oak and poplar.
Put a 20 back on it with the china full chisel does great after a couple
Of sharpenings.

 

[smokey7]

Is your outer spike bent?

 

[Czed]

Is your outer spike bent?

No it's flat i don't think I've ever bent one without breaking something lol
That's one of the husky full wrap kits from bailey's those spike's are thick.
I didn't think i would keep those large spike's on there but they are very handy for bucking.