Saw video thread

[chipper1]

FWIW the 271 runs the same piston as the 261.

So it's only part pro saw .
No wonder it's such a dog.
Thanks though, I did see your video, looks like its running great.

 

[Chainsaw Jim]

 

[RI Chevy]

Nice video Jim! Must have been a Royal pain in the arse to port that clamshell.

 

[Chainsaw Jim]

I reinstalled the elbow and air filter for test cutting. There was a huge loss in air flow and it needed to be leaned up quite a bit to compensate. Still ran good though.
The rakers are set at .025" by gauge. It's looking like I'll need to double that depth for it to feed better.

 

[Chainsaw Jim]

Nice video Jim! Must have been a Royal pain in the arse to port that clamshell.

Most are not all that bad to get into.

 

[RI Chevy]

Hmmm. INTERESTING.

 

[RI Chevy]

Nice Oh90

 

[Chainsaw Jim]

Nice Oh90

Cho90, lol.

 

[MG2186]

We have 5 of those 271’s at work. They seem to be pretty good saw actually. Don’t act nearly as anemic as 290/291’s to me

 

[Dub11]

I reinstalled the elbow and air filter for test cutting. There was a huge loss in air flow and it needed to be leaned up quite a bit to compensate. Still ran good though.
The rakers are set at .025" by gauge. It's looking like I'll need to double that depth for it to feed better.

Is that .404 or 3/8s?

 

[Chainsaw Jim]

Is that .404 or 3/8s?

8 pin .404

 

[Dub11]

8 pin .404

Gonna try a 9 pin?

 

[birdmeter]

I reinstalled the elbow and air filter for test cutting. There was a huge loss in air flow and it needed to be leaned up quite a bit to compensate. Still ran good though.
The rakers are set at .025" by gauge. It's looking like I'll need to double that depth for it to feed better.

throwing big ass chips!

 

[Chainsaw Jim]

Gonna try a 9 pin?

I'd rather jump straight to 10. I also want to swap the bar tip out to 3/8 and run 12 but I'm not sure if they sell a 3/8 replacement tip for that bar.

 

[Dub11]

I'd rather jump straight to 10. I also want to swap the bar tip out to 3/8 and run 12. I'm not even sure if they sell a 3/8 replacement tip for that bar.

Right on.

 

[mdavlee]

I'd rather jump straight to 10. I also want to swap the bar tip out to 3/8 and run 12 but I'm not sure if they sell a 3/8 replacement tip for that bar.

They do. I have changed them out to 3/8” to mill a narrower kerf

 

[deye223]

13 tooth if I'm not mistaken

 

[AlfA01]

Sure as hell don't need more intervention. And you know it

This ^^^^

Hey @T.Roller did you ever get this tree down?

LMAO.

 

[MustangMike]

OK, This may not be allowed, but I'm going to post a Saw Video! My newly created Blue Beast (066 cyl, Meteor Piston) with a touch of porting, in some tough dead White Oak. She is running an untouched (cheapie) 28" B+C. Still on it's first tank, so it is just breaking in.

I also made a Vid of my Dr Al Hybrid in the same wood. The saw did very well, but the video did not come out (lots of pixeling, I think the camera guy must have moved).

 

[RI Chevy]

Nice Mike. Whose the old guy in the Husqvarna helmet???