What's on your bench?

[Tor R]

346?

yup, 2x346 OE

 

[Stihl working Hard]

I have a handful of saws here that I owed people. Here is a 395XP I received completely disassembled and in a box. I don't normally take jobs like this, but this was a bartering deal.

These pics are all after I cleaned everything up.

New clutch springs and bar guide.

The plastic is quite faded, but I cleaned it up and sprayed it down with tire shine. It got new decals as well.

Don't tell anyone, but I forgot to put bar lube in it before running it, lol.

Nice job on the saw there Brad turned out great

 

[Stump Shot]

New Husqvarna blower. Just needed a tune. Why sell directly to folks and make it so that they can't tune it themselves?

 

[Onan18]

This 261 got new bearings, seals, gaskets, fuel line, carb kit, and a new Meteor 262 piston. It has a date to get "bit" in the near future.

 

[Dub11]

New Husqvarna blower. Just needed a tune. Why sell directly to folks and make it so that they can't tune it themselves?

View attachment 90101

Its crazy isn't

 

[Jon1212]

View attachment 90103
View attachment 90104

This 261 got new bearings, seals, gaskets, fuel line, carb kit, and a new Meteor 262 piston. It has a date to get "bit" in the near future.

You get that red and black saw running, yet?......

 

[Onan18]

You get that red and black saw running, yet?......

No but I need to, slacking like there is no tomorrow!

 

[Jon1212]

No but I need to, slacking like there is no tomorrow!

That's okay.....I look forward to the finished product.

 

[Onan18]

That's okay.....I look forward to the finished product.

Me too my friend.

 

[460 magnum]

My uncle picked this saw up for $15 at an auction. He was told it hadn't been run in two years. So he brought it to me to see if I could get it running. I cleaned the carb put some fresh gas in it, gave it a few pulls and runs like a new one. Why cant I find these sweet deals like this? Hate to have to give it back its a neat old saw.

 

[blsnelling]

I didn't know they needed oiling.
Just K&N oil will do I guess?

The early ones do. They actually came with a small container of oil. My dad's first production month 046 has/had one like that.

 

[big t double]

 

[Mattyo]

394 built for a friend....mostly spares I had lying around. But it's got new cabers...new nachis and hyway seals....hyway muff.... new fuel line and filter. New starter cord. High top cover and filter will be new. New carb on its way. Light port work only. Didn't need to touch the transfers much. Ended up at 103 12? 76 I think. 190 comp

Ugly....but it's got it where it counts. I'd have it running if the carb had showed up. ....

 

[Mattyo]

Oh....of note. I just sanded squishband to get rid of the plating lip. Squishband was not cut on the lathe. I did machine the case a bit and did do a gasket delete.

 

[Tor R]

One step forward and two step backwards....even I was careful and went through antibiotica it ended up with infection, spent 2 hour at the dr to cut it clean again (without pain killer), wasn't fun lol.
She said 4-6 weeks


On the good side, my dealer send me picture of my new 346 case with the new case my project is just under 275$ for an low hour 346 xpg Trio Brake, but I gone give my finger 6 weeks without toutching a saw!!

 

[Dub11]

One step forward and two step backwards....even I was careful and went through antibiotica it ended up with infection, spent 2 hour at the dr to cut it clean again (without pain killer), wasn't fun lol.
She said 4-6 weeks
View attachment 90322

On the good side, my dealer send me picture of my new 346 case with the new case my project is just under 275$ for an low hour 346 xpg Trio Brake, but I gone give my finger 6 weeks without toutching a saw!!
View attachment 90323

Give them fingers a rest infections is no fun and no joke.

 

[beaglebriar]

One step forward and two step backwards....even I was careful and went through antibiotica it ended up with infection, spent 2 hour at the dr to cut it clean again (without pain killer), wasn't fun lol.
She said 4-6 weeks
View attachment 90322

On the good side, my dealer send me picture of my new 346 case with the new case my project is just under 275$ for an low hour 346 xpg Trio Brake, but I gone give my finger 6 weeks without toutching a saw!!
View attachment 90323

Sorry to hear that Tor. Take it easy for awhile bud.

 

[Tor R]

Give them fingers a rest infections is no fun and no joke.

Sorry to hear that Tor. Take it easy for awhile bud.

thanks my friends.
I sure will take it easy for the next 4-6 weeks, I actually had less issues with my hearth surgery compared to a stupid finger lol

 

[Cut4fun]

New oem p came in today for my 3.3 and just like I thought :happybanana:. I am going to clean the old one up to use in another saw.

 

[Onan18]

254 XP for my Dad, original cases were junk. Replaced with a set of 261 cases, new bearings, gaskets and seals, Meteor piston, carb kit, clutch drum, rim, clutch drum bearing, bar pad plate, and muffler. Almost done now just waiting on a few smalls, like a fuel tank.