Was a Moe 394, now a Joe 395

[dustinwilt68]

That’s a no no, it would compete too closely to his 660.

Compete insinuates it would be close....

 

[RI Chevy]

When is the last time you cut one down?

About the same time you cut yours down Ken.

 

[Lightning Performance]

About the same time you cut yours down Ken.

This month. Cool. Pics?
Sure. What would you do with a ported 395 and 42" bar, seriously. Do you do big trees.... I had no idea.

I run a 32 or 40 for the big ones but mostly on the mil with the 40.

 

[Moparmyway]

Np on miss matched. You won't be replacing *s-word that doesn't fall off.

I’m not going to be able to send this saw, or most any other saw that I might do in the future, back to its owner with mismatched stuff. If I had to get 3 different tools to remove a cover with 3 fasteners, I’d be a little miffed

That’s a no no, it would stomp a mud hole in his 660.

Fixted it for accuracy

 

[RI Chevy]

Jeeesh. You guys are a tough crowd. Lol

 

[RI Chevy]

This month. Cool. Pics?
Sure. What would you do with a ported 395 and 42" bar, seriously. Do you do big trees.... I had no idea.

I run a 32 or 40 for the big ones but mostly on the mil with the 40.

I like looking at them on my shelf Ken.

 

[longleaf]

huskyboy said: ↑
That’s a no no, it would stomp a mud hole in his 660.
Fixted it for accuracy
Yep

 

[RI Chevy]

Y'all are haterz! Lol

 

[Dub11]

Jeeesh. You guys are a tough crowd. Lol

Get a 3140, tough crowd problem solved!!!

 

[Mattyo]

I’m not going to be able to send this saw, or most any other saw that I might do in the future, back to its owner with mismatched stuff. If I had to get 3 different tools to remove a cover with 3 fasteners, I’d be a little miffed


Fixted it for accuracy

I hate mismatched fasteners too man. I'm with ya. Those top cover bolts and starter bolts always mess me up. They are pricey too.

 

[deye223]

Y'all are haterz! Lol

Narh not haters just people that like saws that piss out fluids where ever they like and fall over all the time ...... hmmm now I get it

 

[RI Chevy]

Get a 3140, tough crowd problem solved!!!

I can't. Kenny says there are no trees here big enough for a hack like me to cut. I guess I only need a homeowner saw...

 

[Deets066]

And away we go...

 

[Dub11]

I can't. Kenny says there are no trees here big enough for a hack like me to cut. I guess I only need a homeowner saw...

3140 are for racing........ no big trees needed.

 

[RI Chevy]

Hmmm. I'm just a hack so I guess I'm not worthy. [emoji2957]

 

[RI Chevy]

And away we go...

Ding ding!!!

 

[Junk Meister]

Thanks Doc !
Mattys tool is just propped there, I never pull or press a bearing into Magnesium, I allways heat the Mag and drop the bearing into place. I never even tried to use the 066 plate .......... great idea !!

The BIG mistake was that I drilled and tapped the top cover side bolt in the wrong location. The calipers show where the center of the hole should be. I didn’t realize the cover I used was tweaked from heat....... so I had to weld it again to fill the hole, then used a new cover and the calipers to do it the correct way.
View attachment 164144 View attachment 164145 View attachment 164146

I knew that this time I read it 'cuz I read that the first time I read this thread.
I hope I will remember/know the next time too.

 

[Moparmyway]

Got the 394/5 & a NIB ported 661 ready for a little time together.

Both running 404 chain, 8 tooth sprockets, 36” bars, off the roll RM




Oh, and also, a box from Greece

 

[huskyboy]

Got the 394/5 & a NIB ported 661 ready for a little time together.

Both running 404 chain, 8 tooth sprockets, 36” bars, off the roll RM

View attachment 189562 View attachment 189563 View attachment 189564 View attachment 189565


Oh, and also, a box from GreeceView attachment 189561

 

[Deets066]

Vroom vroom