The Swap Meet Thread

[Mastermind]

I have a couple pretty nice ones, ill get some pics, yours for the shipping if u desire

No need for pics.


PM incoming.

 

[Tractorsaw1]

Looking for Jonsered 625, 630, 670 later style chain cover & top cover - I have trade items & $$

I have a decent orange 61 husky top cover I would trade for a 625-670 top cover - late or early style

 

[Chris Zautner]

Hello Everyone I'm Looking for some parts for my Stihl 034
looking for a working used oem coil with all the wire leads
outside muffler screw
washer for the chain break handle on the starter that goes around the screw
2 bar nuts
Bar plate the goes on the crank case.
4 handle bar screws

PM me if you have the parts please.
Thank you,
Chris Zautner.

 

[jacob j.]

Ain't got one yet......

I looked extensively through my stuff and never came up with one. I have several 254 covers though, but the one bolt hole is offset.

 

[DexterDay]

Hello @DexterDay , good to see you.

Yeah, had some password malfunctions.

Hope all is well here my friend!

 

[Time's Standing Stihl]

Spicy Hawaiian......

Looks like sexy Hawaiian to me

 

[Jon1212]

ISO 257 stuff....

A better top cover, and a clutch cover.

 

[paragonbuilder]

ISO 257 stuff....

A better top cover, and a clutch cover.

John there is one an hour from me on CL. But it's running and $200. Maybe I could knock them down??
257 Husqvarna chainsaw

http://hartford.craigslist.org/grd/5975536823.html

 

[Jon1212]

John there is one an hour from me on CL. But it's running and $200. Maybe I could knock them down??
257 Husqvarna chainsaw

http://hartford.craigslist.org/grd/5975536823.html

I appreciate the offer, but I spent my project money on one that turned out to be a little less "complete" than advertised. I ordered $30 worth of smalls from @Agrarian, and still have to order rings, and seals for it. The clutch cover is nearly melted through from being run with the brake engaged. At least I got half a tank of bar oil out of the deal dot dot dot

 

[paragonbuilder]

I appreciate the offer, but I spent my project money on one that turned out to be a little less "complete" than advertised. I ordered $30 worth of smalls from @Agrarian, and still have to order rings, and seals for it. The clutch cover is nearly melted through from being run with the brake engaged. At least I got half a tank of bar oil out of the deal dot dot dot

I figured so. I just didn't want to not mention it since I saw it this morning.
How's a 257 run anyhow?

 

[Jon1212]

I figured so. I just didn't want to not mention it since I saw it this morning.
How's a 257 run anyhow?

Well, I appreciate you mentioning that one.

Not sure. Though @Termitebuffet told me that they can be spunky. I was going to build this one for my oldest boy, but it may just stay in a bucket for a while. I'll probably just give him my Poulan Pro Super 380, set up with a 20" combo.

 

[huskihl]

How's a 257 run anyhow?

Well, I appreciate you mentioning that one.

Not sure. Though @Termitebuffet told me that they can be spunky. I was going to build this one for my oldest boy, but it may just stay in a bucket for a while. I'll probably just give him my Poulan Pro Super 380, set up with a 20" combo.

It's an open port cylinder with similar construction to a 51/55 that does well ported. Also, there have been a few 262xp jug swaps that might be worth looking into

 

[jacob j.]

I appreciate the offer, but I spent my project money on one that turned out to be a little less "complete" than advertised. I ordered $30 worth of smalls from @Agrarian, and still have to order rings, and seals for it. The clutch cover is nearly melted through from being run with the brake engaged. At least I got half a tank of bar oil out of the deal dot dot dot

Dot dot dot...I got 257 parts for you.

 

[Jon1212]

Dot dot dot...I got 257 parts for you.

Oh! Do tell...

 

[Mark71gtx]

Edit - didn't need the part after all. On a bright note, I got my 65L started tonight!

 

[DexterDay]

I have a MS 460 piston and cylinder kit (aftermarket that was bought through HL supply) that I'd trade for a 16" large mount Husqvarna bar in .050?

Any takers? Not brand specific on the bar. Just ask that it's in decent shape and usable.

 

[beaglebriar]

Looking for a hda199 carb and a 357/359 elbow to stick on my 353. Have some parts or cash to trade.

 

[Wagnerwerks]

I have to see how many I have left. I'll check for you.

 

[beaglebriar]

I have to see how many I have left. I'll check for you.

Cool Thanks Chris

 

[Wagnerwerks]

I'm down to the one I need. If I run into another before you find one... I'll pass it along. I'm going to look at some saws friday.