DOLMAR/MAKITA The Official Sachs Dolmar Dolmar Makita Dolmar Chainsaws Thread

[Wilhelm]

Exactly why I asked you. I got some backup AV. Need to get clutch and drive parts next order. Thank you.

Get a spare oil pressure line, apparently that is where these saws start to leak.

 

[RCBS]

Get the clutch 139 and a drum 189.

I go with the logic that the clutch is a set and should be replaced as such.

I have been told that the drum hub is prone to separation from the drum, although I never had that happen myself.

Get a couple spare E-clips 146, they randomly open black holes and vanish in them!

Got three E clips inbound. Pressure line covered on previous order. (x2)

 

[RCBS]

Thanks for the help gentlemen. I'm to the point now of needing to know that I'm buying the 'right' spares as I've already gotten most of the 'cheap' stuff. If I do ever have a catastrophic I just plan to retire the current runner and turn it into a parts emporium for one still in the box.

 

[branko]

What is the piston ring thickness for Dolmar 103? Thank you

 

[mgr1]

What is the piston ring thickness for Dolmar 103? Thank you

1.5mm

 

[Wilhelm]

What is the piston ring thickness for Dolmar 103? Thank you

BOk. Znaš li za dolmar 103 ili 105 debljinu ringa na batu?

Dolmar part number 108-132-240

 

[RCBS]

Parts order arrived from two different warehouses today. Will get the clutch and pump drive on next order sometime in the new year. Time of the year to think of others is upon us.

 

[EchoShindaiwaMakitaDolmar]

Parts order arrived from two different warehouses today. Will get the clutch and pump drive on next order sometime in the new year. Time of the year to think of others is upon us.


View attachment 441207

Out of curiosity, are the chains made in USA or Canada? I've read that Oregon is having chain made in china now. Thanks

 

[Hulsty]

Nice parts haul, I need to do similar for my 7901, where did you order from?

 

[RCBS]

Out of curiosity, are the chains made in USA or Canada? I've read that Oregon is having chain made in china now. Thanks

These are US made. Older stock I assume. They no longer sell a 20" 3/8 wearing saw.

Nice parts haul, I need to do similar for my 7901, where did you order from?

Directly from Makita. A work perk. I plan to keep this stuff alive for as long as I care to use it. Everyone whinges about parts availability...but I've not been denied anything I've asked them for yet.

 

[Hulsty]

Looking at a spare coil for my 7901, is this what I need?

Dolmar ignition coil PS630 PS6400 PS6401 PS7300 PS7301 PS7900 DCS642120 DCS6401 | eBay Australia

DCS642120 64 cc. DCS6401 Gasoline Chain Saw. Dolmar ignition coil.

www.ebay.com.au

 

[SOS Ridgerider]

Looking at a spare coil for my 7901, is this what I need?

Dolmar ignition coil PS630 PS6400 PS6401 PS7300 PS7301 PS7900 DCS642120 DCS6401 | eBay Australia

DCS642120 64 cc. DCS6401 Gasoline Chain Saw. Dolmar ignition coil.

www.ebay.com.au

Yes, that'll work.

 

[hbabler]

Hopefully you guys can help me out a bit.
My NOS EA7900 got a workout today (or gave me a workout….)
I took it out for a wildland class and it would die when idled.
Not consistently but when I was lining up my backcut every couple of times it would idle down and die. It died a couple of times when I got tangled up in some thorns as well.

Sometimes I could catch it and keep the idle up, I adjusted the idle speed up a bit and that had no affect in addition I turned the low speed mix up a bit as well with no changes.

It’s running 32:1 fuel, and I didn’t see any issues that stuck out to me. I definitely need to get this sorted out. Any ideas?

 

[hacskaroly]

Parts order arrived from two different warehouses today. Will get the clutch and pump drive on next order sometime in the new year. Time of the year to think of others is upon us.

You are supposed to wait until Christmas Day to open your presents!!

Not consistently but when I was lining up my backcut every couple of times it would idle down and die. It died a couple of times when I got tangled up in some thorns as well.

When was the last time you did any carb work on the saw? Possible you have some crusty diaphragms or dirty jets. Here is a good video that explains some causes for chainsaws to bog and die while idling.

 

[Yukon Stihl]

Did you adjust the carb lately?

 

[EchoShindaiwaMakitaDolmar]

Hopefully you guys can help me out a bit.
My NOS EA7900 got a workout today (or gave me a workout….)
I took it out for a wildland class and it would die when idled.
Not consistently but when I was lining up my backcut every couple of times it would idle down and die. It died a couple of times when I got tangled up in some thorns as well.

Sometimes I could catch it and keep the idle up, I adjusted the idle speed up a bit and that had no affect in addition I turned the low speed mix up a bit as well with no changes.

It’s running 32:1 fuel, and I didn’t see any issues that stuck out to me. I definitely need to get this sorted out. Any ideas?

You did say it's a new/NOS saw that hasn't been in wood until now, correct? Was it ever fueled prior to the wildland class?

Just a thought- if you're using the optional foam cover over your air filter- perhaps the air flow is insufficient. Remove it and see what happens.

 

[hbabler]

It had not been fueled prior to last week when I fueled it and started it to make sure it ran.

It has the HD filter with the foam cover on it. I’ll try it without

 

[hbabler]

You are supposed to wait until Christmas Day to open your presents!!


When was the last time you did any carb work on the saw? Possible you have some crusty diaphragms or dirty jets. Here is a good video that explains some causes for chainsaws to bog and die while idling.

It hasn’t had any work done to it.

 

[hbabler]

Did you adjust the carb lately?

I adjusted the low speed jets a bit to try and fix it. That being said I haven’t fully adjusted it. I’m a bit wary of it due to the limited coil but I guess there is no better time than the present to learn it.

Any suggestions on videos or references for adjusting it?

 

[Wilhelm]

Tach her just shy of the 12.8k rpm limit and she'll be fine.

That is how I tune my saws including my MMed PS-7310 (EA7300).