So what did you buy today

[dangerousatom]

Bought a junked out filthily T540xp of eBay for $71.00 shipped It was said to have low compression, and the break handle is snapped. Ill just assume it was dropped out of a tree.....well see what comes of it.

 

[Czed]

I ordered a couple of these hand made in El Salvador condor knives
I have the larger low drag version and it's my favorite large knife

Condor Swamp Romper Knife (4.75") for Sale $66.81

Overall: 9.75"; Blade: 4.75" l 1075 Carbon Steel l Standard Edge; Handle: Black l Walnut; Other Info: Full Tang l Lanyard Hole. Brown leather belt sheath.

www.chicagoknifeworks.com

The sheath's alone from condor are excellent I've seen similar less quality sheath's sell for 40+ dollars.

 

[jblnut]

Wondering, are these disc attachment nuts?

Yes they are. 30” blades with around 1,100lbs of downforce on each of them. Makes my 500hp tractor bark a bit.

Assuming the forklift / breaker bar combination is a known torque?

“At least 3,000ft/lbs” Forklift will lift 6,000lbs so I should have “at least 3,000ft/lbs” with the lift point 2’ from the socket

 

[Partner]

Mine are 18" and 16" slightly worn

 

[Partner]

A nice black Emak spool 12 years old and 2 Chinese ones. The orange one is new and the fuel lines have arrived / The chain is probably 0.404"

 

[They call me Mr. Kibbs]

Yes they are. 30” blades with around 1,100lbs of downforce on each of them. Makes my 500hp tractor bark a bit.
View attachment 456828

“At least 3,000ft/lbs” Forklift will lift 6,000lbs so I should have “at least 3,000ft/lbs” with the lift point 2’ from the socket
View attachment 456822

Yeah, I'd say that ought to do it! Big equipment for big open flat spaces, don't see a whole lot of either around here

Appreciate the time taken to explain, different worlds!

 

[heimannm]

McCulloch 4 HP air cooled outboard motor. Same basic engine block as the 80cc chainsaws.



I also ordered a few small items (o-rings, spiral retaining rings, a few bolts) to get my Struck Magnatrac back in working order.



Mark

 

[Wilhelm]

1 1/2 dozen 9" angle grinder cutoff & grinding wheels, on sale 6 for 4€.



And 2000 zip ties, various sizes.

 

[rogue60]

Was sitting on the shelf in the shop covered in dust. I kind of felt sorry for it... Nobody wanted to take this beast home?.....
Seems all the homeowners buy 500i's or 3120's nowadays..
I Can't remember the last time I've seen an air filter this clean? I feel the need too get it filthy asap!

 

[Wilhelm]

Tiniest welder I have ever seen, inverter, single phase, 110Amp max



And some heavy duty nylon trimmer line, square, 3.3mm/.13" gauge

 

[SimonHS]

Tiniest welder I have ever seen, inverter, single phase, 110Amp max

View attachment 457102

And some heavy duty nylon trimmer line, square, 3.3mm/.13" gauge

View attachment 457103

That welder looks good. Tiny form factor. Looks like it needs 20.8A at 230V input. Shame it doesn't have a 13A plug. You might need to be careful where you plug it in?

Captcha

 

[Partner]

That welder looks good. Tiny form factor. Looks like it needs 20.8A at 230V input. Shame it doesn't have a 13A plug. You might need to be careful where you plug it in?

View attachment 457106

Captcha

I changed the 230v sockets to the blue ones like in the camper

 

[Wilhelm]

That welder looks good. Tiny form factor. Looks like it needs 20.8A at 230V input. Shame it doesn't have a 13A plug. You might need to be careful where you plug it in?

View attachment 457106

Captcha

No worries, those 20Amps are peak.
Our outlets support 16Amps extended, and 10 or so Apms continuous.

I am sure it will work just fine if I can run my inverter 120Amp flux wire welder laying a continuous 4" long bead in multiple layers at max output (label says 17Amps max draw!).

 

[Wilhelm]

Proven flux wire welder, no issues whatsoever.


New stick welder.
We'll see how that goes.

 

[Wilhelm]

So cute!

 

[Partner]

Usually, the socket is already available with a 1kV water pump / there are different sockets and different manufacturers

 

[SimonHS]

This should last me for a while.

 

[Powerstroke Cowboy]

Bought the motoseal today. The plugs showed up in the mail today.

 

[Partner]

This should last me for a while.

View attachment 457153

View attachment 457152

What price

 

[ZERO]

@Powerstroke Cowboy 7A series hopefully made in JAPAN.

The CMR series 6H/7H I purchased last year, all made in Thailand.

As pointed out by our good friend Rich Flagg.