Saw video thread

[Stump Shot]

Thanks. I still need to try a timing bump that @Stump Shot told me to..
Saw turned out pretty good for being primarily left over parts.
And I still want to wire up the heated handles sometime soon.

Don't let its lineage bother you, a mutt can surprise you once in a while.

 

[RI Chevy]

Nice Steve!

 

[huskyboy]

046/460 really seem to come alive with mods/porting. I’m not particularly blown away by them stock.

 

[Stump Shot]

046/460 really seem to come alive with mods/porting. I’m not particularly blown away by them stock.

More like a torque version of the 044/440.

 

[mdavlee]

Video of the 17k, please

Deets had it for a little while. It lived fine after wards. It didn’t make much power up there though. Exhaust at 92.

 

[mdavlee]

Regardless i want video!

I know my 064 that @srcarr52 did for me will do it. We have both seen it.....But I definitely dont run it there, no powa

Maybe i should get a picture of the tach, that seems like the cool thing to do

I’ll never do it. I don’t have any of those saws anymore. My 346 XS might go that high but I doubt it.

 

[huskihl]

I’ll never do it. I don’t have any of those saws anymore. My 346 XS might go that high but I doubt it.

15,5 maybe. Hard to get that high with the exhaust at 110. But they dont usually care which bar you mount on them

 

[mdavlee]

15,5 maybe. Hard to get that high with the exhaust at 110. But they dont usually care which bar you mount on them

I won’t try it then. Probably wouldn’t make 3 cuts in an 8x8 without being too lean by the 3rd

 

[redline4]

Don't let its lineage bother you, a mutt can surprise you once in a while.

I am hoping it can make a trip up to you this winter.

 

[redlight066]

Got to play at work a little yesterday. Terry is the lead climber and a super nice guy in our Charlotte office. Sent his saw down for some light maintenance. He got a little more than that. Lol. I did some light port work, bumped the timing and opened up the muffler.

 

[RI Chevy]

Nice!

 

[huskyboy]

I swapped this ported 7910 with 046 piston topend to another 6421 chassis. The bottom end it was on was going out (pto bearing play). I decided to do a little work to the jug/piston while it was apart. On first start it was sucking the choke shut on full throttle and I had to wind the spring tighter. After that I ran a 32” and 8 pin full comp in oak to stress test it.

 

[RI Chevy]

Nice Mason.

 

[huskyboy]

Nice Mason.

Wanna race?

 

[Edwad]

I swapped this ported 7910 with 046 piston topend to another 6421 chassis. The bottom end it was on was going out (pto bearing play). I decided to do a little work to the jug/piston while it was apart. On first start it was sucking the choke shut on full throttle and I had to wind the spring tighter. After that I ran a 36” and 8 pin full comp in oak to stress test it.

Nice!

 

[Deets066]

Wanna race?

Yup

 

[RI Chevy]

Wanna race?

Yes. You want me to run my Stock 026 or ported 036?

 

[huskyboy]

Yes. You want me to run my Stock 026 or ported 036?

Ported ms460

 

[Deets066]

Ported ms460

Same chain....

 

[Canadian farm boy]

Ported ms460

or maybe one of his other 77cc saws