Saw video thread

[Definitive Dave]

Lol

 

[huskihl]

Who ported that 064

Looks like he's been watching jms vids

 

[Cracker Boy]

Looks like he's been watching jms vids

Real funny I was only politely asking because i would have thought it would have stated who ported each saw in videos.im in market to get a 064 done in near future is why im asking.i hope that this is just a joke and not sarcasim.thanx

 

[huskihl]

 

[Cracker Boy]

This one here jms ported

Thanx for info

 

[huskihl]

Real funny I was only politely asking because i would have thought it would have stated who ported each saw in videos.im in market to get a 064 done in near future is why im asking.i hope that this is just a joke and not sarcasim.thanx

Dang dude. Wasn't meaning any harm.
I watched his vids. He cuts like he's been watching jms vids. You know..hold the tip of the bar over the log for 5 seconds at 1/4 throttle (like you're scared of what's about to happen), nut it as you lay it on the log, and then slide the saw forward to the dogs like it's the .050" rakers that are pulling it in. Yet the saw still climbs to 12k rpm in the cut.

Must be "maxed out".

 

[Deets066]

Dang dude. Wasn't meaning any harm.
I watched his vids. He cuts like he's been watching jms vids. You know..hold the tip of the bar over the log for 5 seconds at 1/4 throttle (like you're scared of what's about to happen), nut it as you lay it on the log, and then slide the saw forward to the dogs like it's the .050" rakers that are pulling it in. Yet the saw still climbs to 12k rpm in the cut.

Must be "maxed out".

 

[Cracker Boy]

Dang dude. Wasn't meaning any harm.
I watched his vids. He cuts like he's been watching jms vids. You know..hold the tip of the bar over the log for 5 seconds at 1/4 throttle (like you're scared of what's about to happen), nut it as you lay it on the log, and then slide the saw forward to the dogs like it's the .050" rakers that are pulling it in. Yet the saw still climbs to 12k rpm in the cut.

Must be "maxed out".

Ok

 

[RyeThomas]

Don’t have a video yet but may tomorrow, and yet again I’ve proven I’m an idiot. I’ve been looking for a 661since I sold my last one to help fund a few things and low and behold a homeowner about 20 miles from me purchased one and decided it was way to much saw and put it on CL. Posted at 7:00 am and I messaged him at 7:30 ish. Was in my truck by 10:30. Not a homerun deal but very fair.
My MMWS 461r is more than enough saw but I really like an Mtronic saw, keeps me from being me (aka breaking everything I touch).

 

[Manofstihl066]

64 looks awesome. Pulls the long bar with authority.

 

[Cracker Boy]

Don’t have a video yet but may tomorrow, and yet again I’ve proven I’m an idiot. I’ve been looking for a 661since I sold my last one to help fund a few things and low and behold a homeowner about 20 miles from me purchased one and decided it was way to much saw and put it on CL. Posted at 7:00 am and I messaged him at 7:30 ish. Was in my truck by 10:30. Not a homerun deal but very fair.
My MMWS 461r is more than enough saw but I really like an Mtronic saw, keeps me from being me (aka breaking everything I touch).
View attachment 93705 View attachment 93706

What did u give if you dont mind my asking

 

[TreeLife]

This one here jms ported

Got you a real runner there

 

[RyeThomas]

Don’t mind at all bud I paid $750, he estimated 10 tanks of fuel total, born on date of 7/16 with a 25” Stihl ES bar. I looked her over and it’s a really clean saw so I don’t doubt him a bit. I made it dirty before the pics doing test cuts. Those pics don’t do it justice.

 

[Cracker Boy]

Don’t mind at all bud I paid $750, he estimated 10 tanks of fuel total born on date of 7/16 with a 25” Stihl ES bar. I looked her over and it’s a really clean saw so I don’t doubt him a bit. I made it dirty before the pics doing test cuts. Those pics don’t do it justice.

Nice buy im gonna get one someday.its super clean saw.good score

 

[Jswanson]

Dang dude. Wasn't meaning any harm.
I watched his vids. He cuts like he's been watching jms vids. You know..hold the tip of the bar over the log for 5 seconds at 1/4 throttle (like you're scared of what's about to happen), nut it as you lay it on the log, and then slide the saw forward to the dogs like it's the .050" rakers that are pulling it in. Yet the saw still climbs to 12k rpm in the cut.

Must be "maxed out".

And the masses was amazed by the *dipstickery.

 

[huskihl]

And the masses was amazed by the *dipstickery.

From *dipstickery to *pretty boyery

 

[huskyboy]

 

[TreeLife]

Mason, run ten tanks thru it after the mod and post another video

 

[Dub11]

Don’t mind at all bud I paid $750, he estimated 10 tanks of fuel total, born on date of 7/16 with a 25” Stihl ES bar. I looked her over and it’s a really clean saw so I don’t doubt him a bit. I made it dirty before the pics doing test cuts. Those pics don’t do it justice.

Thats you suck territory there lol.

 

[huskyboy]

Mason, run ten tanks thru it after the mod and post another video

Can't remember how many tanks I put through it since the mod, probably 5-6. Roughly 12 tanks on it all together, it's still shiney and new lol . One of my favorites to run.