Saw video thread

[WillG]

Cutting some nice hahd New England Red Oak with the 029 Super I just got running.

Sent from my E6910 using Tapatalk

 

[andyshine77]

How about some 500i action.[emoji12]

 

[ZukiRyder400]

My final revisions on the x torq. Timing is all the same just slapped a chinesium 395 carb on there to see how it would run. I know that chain sucks... i took a little more than I wanted to off the rakers.. now i use gauge lol.

 

[Hinerman]

Very nice Boss! Still the King of the 60cc saws!!! It looks like you solved the torque problem that everyone was looking for a few years ago.

 

[huskihl]

Very nice Boss! Still the King of the 60cc saws!!! It looks like you solved the torque problem that everyone was looking for a few years ago.

The chain could probably use a new edge. But the saw has quite a bit better torque than stock

 

[BuxtonSaws]

My current favorite 60cc model to do

Sent from my Pixel 4a using Tapatalk

 

[RI Chevy]

Nice job. Runs strong.

 

[farminkarman]

My current favorite 60cc model to do

Sent from my Pixel 4a using Tapatalk

Looks to be a good runner! How long have you been doing saws? Where in Wisconsin are you at?

 

[BuxtonSaws]

Looks to be a good runner! How long have you been doing saws? Where in Wisconsin are you at?

Repair work forever....Porting Around four years... Full time since January. I'm in Brodhead

Sent from my Pixel 4a using Tapatalk

 

[Hinerman]

My current favorite 60cc model to do

Sent from my Pixel 4a using Tapatalk

Please tell me that is not a stock carb...

 

[BuxtonSaws]

Please tell me that is not a stock carb...

It is... It's just a normal woods ported saw..nothing crazy done to it. I've never had a problem with them supplying enough on a build like that. I am interested in why you ask though. I don't mind criticism that's how we learn and grow.

Sent from my Pixel 4a using Tapatalk

 

[Hinerman]

It is... It's just a normal woods ported saw..nothing crazy done to it. I've never had a problem with them supplying enough on a build like that. I am interested in why you ask though. I don't mind criticism that's how we learn and grow.

Sent from my Pixel 4a using Tapatalk

No criticism from me. I ask because the only 361 I have seen run as good as yours had a bigger carb (044 carb maybe); it is a beast. I have a ported 361 but don't think it runs as good as yours; hard to really tell though. I do like mine regardless. Anyhow, very nice job on the 361; good RPMs, good torque, and a good chain never hurts---even more impressive knowing it has a stock carb.

 

[BuxtonSaws]

No criticism from me. I ask because the only 361 I have seen run as good as yours had a bigger carb (044 carb maybe); it is a beast. I have a ported 361 but don't think it runs as good as yours; hard to really tell though. I do like mine regardless. Anyhow, very nice job on the 361; good RPMs, good torque, and a good chain never hurts---even more impressive knowing it has a stock carb.

I've tried 044 carbs in the past.. I didn't feel the gain was worth the trouble for a work saw ....on the one I did it too... If I was trying to go all out I probably would go that route again though... I do feel it helps.

Sent from my Pixel 4a using Tapatalk

 

[huskyboy]

My current favorite 60cc model to do

Sent from my Pixel 4a using Tapatalk

Those saws rip with a 20” bar cutting firewood, fun little rippers.

 

[BuxtonSaws]

One more... I enjoy these saws also they really come to life

Sent from my Pixel 4a using Tapatalk

 

[TreeLife]

One more... I enjoy these saws also they really come to life

Sent from my Pixel 4a using Tapatalk

3/8 on that one, Gary?

 

[BuxtonSaws]

3/8 on that one, Gary?

20 inch .325 I believe. They will handle 3/8 though.

Sent from my Pixel 4a using Tapatalk

 

[ZukiRyder400]

FINALLY done tweakin on my 2159. This recipes a keeper. Tuned kinda rich

 

[Dolkitafreak]

First echo I've ever modded, snorty little things. Thanks @Red97 for the lathe work. And yes, I know I'm not cutting concrete, shame on me...

 

[ZukiRyder400]

First echo I've ever modded, snorty little things. Thanks @Red97 for the lathe work. And yes, I know I'm not cutting concrete, shame on me...

Strong little bugger! Good job