Ported 390xp vs. Ported MS460

[huskihl]

Whatcha got goin on there, Mr Lee?

 

[mdavlee]

Whatcha got goin on there, Mr Lee?

Few different carbs. The top is a stock 372, 660, big walbro, and the 084 carb.

 

[Moparmyway]

If you want it to win, you better get Levi to run it..
Lol..

Lemme know when they are ............
If'n I can get my 288/066 built by then, Levi should be the double down bet !

Are you going?

A couple of my saws will be there

 

[mdavlee]

Lemme know when they are ............
If'n I can get my 288/066 built by then, Levi should be the double down bet !




A couple of my saws will be there

July 9th[emoji6]

 

[Keith Gandy]

9010's a 52 mm bore too..

Even longer stroke.

Yall keep talkin and out that info and Im pickin it up!!

 

[MustangMike]

"A couple of my saws will be there"

Specifics, what saws and who is gonna have them, and why aren't you coming??? (I know, I'm worse than your Mother, right!)

 

[Moparmyway]

"A couple of my saws will be there"

Specifics, what saws and who is gonna have them, and why aren't you coming??? (I know, I'm worse than your Mother, right!)

You'll just have to be there, you'll definately hear them, they aint quiet .............. probably the loudest 90cc muther-scratchers there.

 

[David Young]

any idea what was done to the 390?

 

[mdavlee]

any idea what was done to the 390?

Not enough evidently LOL

 

[Chainsaw Jim]

any idea what was done to the 390?

I'll find out tomorrow when I'm rebuilding the carb.

 

[Chainsaw Jim]

Here's my 75cc 372xpw and 576xp unlimited coil non-autotune version with the same bar, chain, and log.

 

[mdavlee]

576 looks to be a hair faster. They always impressed me.

 

[Chainsaw Jim]

The best timing I can get on it is 15 seconds for the fastest cut with the 372 and 12.5 for the 576.

 

[mdavlee]

Yep. About what I got from the counter on the video. 576 pretty well as fast as the 064.

 

[Keith Gandy]

The best timing I can get on it is 15 seconds for the fastest cut with the 372 and 12.5 for the 576.

What r the rakers on your chain set at?

 

[Chainsaw Jim]

I'll have to measure and see. I usually free hand file my chains and don't measure.
Side raker removal can be as important as raker height. This particular chain has the numbers filed off the sides and the raker height is close to factory from what I remember seeing when I laid a flat edge to see where they were when I was done.
I also cleaned the gullets and they took an edge too...whether it actually makes contact with wood to help is something for NASA scientists to figure out. Lol

 

[Hinerman]

My 2186 ain't as fast as 064/066 but I still love it, dam bit sexier for sure!

Your 2186 is faster than 95% of the ported 066's out there.

I sat in my truck and watched you guys cut in the rain for 2+ hrs at the Iowa GTG. This 2186 was the saw that made me get out and cut. It is very very impressive.

 

[MustangMike]

Good running saws can come if various flavors.

 

[Hedgerow]

576 looks to be a hair faster. They always impressed me.

Hooray Mr. Fluffy??

576xpAT was a bad dude.

 

[Homelite410]