Miller Mod and the PS-421 dolmar.

[Miller Mod Saws]

But that said. It's gonna take more than just a carb. It would take the whole intake track.

 

[smokey7]

That 421 is a way better running ssw. Lets see it limb a tree Nd buck a log or two. Use the dogs tho. If i cut all day without dogging in id be so wore out by lunch id not have anything left to give.

 

[Backtroller]

I'd like to see an unlimited coil for it. Wish there was one that bolt up to test it against.

I'm enjoying watching your tests

 

[drf256]

Looks really good Carl. Both do.

You're making a nice light little saw that's highly usable. Great job.

Too late now, but I'm still curious what 123-125/6 woulda done across those 3 port transfers.

 

[jacob j.]

I didn't think the lower intake would help but I was wrong on that. I'm guessing it's due to the small carb. With more carb the higher intake maybe better.

How big is the mixing area in the case?

 

[Miller Mod Saws]

How big is the mixing area in the case?

I'll try and grab a pic when I tear one back down. There not tight compared to say a 7910. But not as big as saw a 346xp.

 

[Miller Mod Saws]

Ok boys excuse this first vid but I was running out of daylight. I now have this makita where I want it. It's been apart a couple times since the last vid but it's now sitting at 107/123/80.

 

[Miller Mod Saws]

I'm done with these 2 saws. Future testing will be done. Little tweaks at a time as a build more of these. That said. The Dolmar is at 105/122/80. This saw is actually a tad faster but takes just enough of a lighter hand that I like the makita at 107/123/80 better for bucking. For light limbing I like the dolmar better. Lol. You would think 2 degrees would be noticeable but it is.

 

[Miller Mod Saws]

For this vid I put on a loop of ps stihl chain. So first cut I'm learning the chain but you guys wanted to see it being dogged so here it is in some locust. Again sorry for the crappy vid.

 

[Miller Mod Saws]

And you wanted to see it limbing!

 

[Miller Mod Saws]

Any questions on this build please let me know. I will try and answer them. Lol.

 

[CoreyB]

Any questions on this build please let me know. I will try and answer them. Lol.

If I was smart enough to have questions I am sure I would be asking. Lol. Looks really good though.

 

[Miller Mod Saws]

If I was smart enough to have questions I am sure I would be asking. Lol. Looks really good though.

Man your smart. I can't make Coffee.

 

[Time's Standing Stihl]

Sounds good limbing Carl!

Sent from my SM-G900R4 using Tapatalk

 

[Miller Mod Saws]

Sounds good limbing Carl!

Sent from my SM-G900R4 using Tapatalk

Thank you!

 

[Miller Mod Saws]

On to the next experiment. Lol tweaking on another pair of 5105s. Playing with the transfer entry angles on these 2. Lol. @mdavlee i know ya like this discussion.

 

[Red97]

Sounds real good...

Nice job sir.

 

[exSW]

For this vid I put on a loop of ps stihl chain. So first cut I'm learning the chain but you guys wanted to see it being dogged so here it is in some locust. Again sorry for the crappy vid.

That's what I'm talking about there.

 

[smokey7]

To me i think they both have there place and shinebin them. The dogged in bucking is more about the load transitions than anythibg else. Thank you for showing the saws working like they should.

 

[Miller Mod Saws]

Well boys it's official. This one is all cleaned up and ready for its new owner. That said I called tonight to order another one and I'm sad to say there will be no more. If I order them now they are makitas in red. Lol.