3/8 LP Drum and Sprocket

[Simondo]

A hardware store chain sold them cheap here for a while, but I didn't bite, wasn't even tempted.

Apart from that, the only way to buy Dolmar saws in Norway is to order them from Makita. There is no dealer network.

Your in the fortunate position to have Jonsered in Norway !!

 

[fordf150]

 

[Deets066]

Was this the thread where we were goin to buy some picco rims? I remember wanting some and somewhat placing an order?

 

[jake wells]

i would like to know the part numbers to the pico sprocket and drum for a ms 250 stihl.

 

[Keith Gandy]

Im still lookin for a picco sprocket for small mount husky or a gb standard spline picco to fit a 562 drum

 

[fordf150]

Im still lookin for a picco sprocket for small mount husky or a gb standard spline picco to fit a 562 drum

Pictured above. That is pico to fit small spline and 404 standard spline rims turned down for use with pico

 

[Keith Gandy]

Pictured above. That is pico to fit small spline and 404 standard spline rims turned down for use with pico

Will the 7t fit a 550xp?

 

[jake wells]

Will the 7t fit a 550xp?

i would like to know also and would 3/8 lp work ok on a .325 bar.

 

[concretegrazer]

Will the 7t fit a 550xp?

You'll need the small spline for the 550.

i would like to know also and would 3/8 lp work ok on a .325 bar.

No.

 

[Homelite410]

Humm I have a file. I don't have a 421 yet, but I have a file.

You are going to need a carbide file.........

 

[Keith Gandy]

You'll need the small spline for the 550.
I think thats it though isnt it that they dont make a small splined husky picco rim? I heard a 562 drum is to be used on a 550 and a gn standard splined picco rim works?



No.

 

[SawTroll]

Im still lookin for a picco sprocket for small mount husky or a gb standard spline picco to fit a 562 drum

I have only seen those GB rims advertised in the UK.

http://www.chainsawbars.co.uk/products/catlisting/category/special-offers/

Sugihara bars in .058, and in other configurations than the light pro ones can be found on the same site.

 

[Keith Gandy]

I have only seen those GB rims advertised in the UK.

http://www.chainsawbars.co.uk/products/catlisting/category/special-offers/

Dang!!! 2 rims would cost 75 US $ to get to me

 

[SawTroll]

You'll need the small spline for the 550.

.....

...unless you put a 562xp drum on it.

 

[SawTroll]

Dang!!! 2 rims would cost 75 US $ to get to me

Sounds like very expensive shipping!

 

[SawTroll]

View attachment 19445

I lke the look of those turned down .404 rims, but how much do they cost?

 

[exSW]

It shouldn't be that much. Shipping from UK isn't usually that bad. Where's ajschainsaws?

 

[Keith Gandy]

Sounds like very expensive shipping!

29.50 . British currency right ? 1
£ to 1.44 Us. 29.50£ shipping

 

[drf256]

Will the 7t fit a 550xp?

The Stihl 3/8lp sprocket can be opened up fairly easily on a lathe. There will still be teeth marks that can be made just a bit deeper to fit.

I'm using a small mount regular 3/8 7T on my echo (like Saw4fun does) and a picco chain with zero issues.

 

[Keith Gandy]

The Stihl 3/8lp sprocket can be opened up fairly easily on a lathe. There will still be teeth marks that can be made just a bit deeper to fit.

I'm using a small mount regular 3/8 7T on my echo (like Saw4fun does) and a picco chain with zero issues.

Im running a regular 3/8 rim for lp. Doesnt fit perfect