Old carb ID help

[Homemade]

This carb is from my old Lombard model 5. It has a power products AH-80 for an engine. I'm not sure of the carb and which is the high needle and which is the low. It runs and idles but any combination of turning either screw doesn't help smoothen things out. But it has ben sitting for 5 years or so since it last ran and quite a few years before that.

Looking at the left side. There is a screw above the throttle shaft. I believe it is the high side but not sure

This is the right side. The big knob at the bottom does have "start" written on it and numbers around the outside.


Sent from my iPhone using Tapatalk

 

[backhoelover]

look like a tillotson hl series. could be on the carb somewhere

 

[Homemade]

I would think so but the fuel inlet is on the wrong side compared to the HL series


Sent from my iPhone using Tapatalk

 

[backhoelover]

Might have to pull carb and clean to find some numbers @ray benson might can help with a ipl he our older saw tech info guru

 

[peter92]

look like a tillotson hl series. could be on the carb somewhere

Its the same carb thats on my Big 10 , the carb no is on the plate on the bottom of the carby

 

[Homemade]

Could be. But there is a part of the frame that covers the bottom of the carb. I'll have to remove it to get a better look.


Sent from my iPhone using Tapatalk

 

[backhoelover]

Its the same carb thats on my Big 10 , the carb no is on the plate on the bottom of the carby

Do you happen to know what kit your saws carb took

 

[backhoelover]

You know low will have to be closest to engine

 

[backhoelover]

Looks like there is about 4 adjustment screw in that carb lol

 

[Homemade]

You know low will have to be closest to engine

No I didn't know that. I'm not a carb guy.


Sent from my iPhone using Tapatalk

 

[peter92]

Do you happen to know what kit your saws carb took

same as HL , HC

 

[backhoelover]

I think I got a azz load of them diaphragms from where I bough a carb gasket lot. Are they hard to come by? They are new

 

[peter92]

I think I got a azz load of them diaphragms from where I bough a carb gasket lot. Are they hard to come by? They are new

I had to get mine from USA direct but should be easy over there to get hold of

 

[peter92]

This is the carb kit DG-5-HL
Tecumseh 2-cycle carburetors seem to all share a common diaphragm and needle & seat, but there may be exceptions. These are fairly easy to locate.

 

[67L36Driver]

That don't look like any Tilly HL or HC that I've ever com across.

Resembles the Carter NRD on my Mall if nothing else.


BTW: Kits and diaphragms are everywhere for the Tilly HL. The HC is the same without fuel pump chamber.

 

[67L36Driver]

Carter NRD. Fuel inlet has large filter under the hex fitting. Large knob is HS jet.

 

[peter92]

Carter NRD. Fuel inlet has large filter under the hex fitting. Large knob is HS jet.

also im sure they need to be tuned when cutting , ive read that some where , but cant remember for the life of me where it was ,

 

[Homemade]

We have a winner, it's a tilly

HIA never heard of it. Will a hl kit work?

Sent from my iPhone using Tapatalk

 

[67L36Driver]

All them slotted brass thingys are passage plugs. No doubt at all to see if they are clear/clean.

 

[Homemade]

And the missing bottom screw.


Sent from my iPhone using Tapatalk