Search results

I purchased a minty 1997 husky 257, replaced spark plug and fuel line and filter, it is working fine but I am worried about the crank seals. Should they be replaced or leave well enough alone! I do not have the tools to vac/pressure test.

What size skf bearings go in. Husky 262xp crank Is it 6202 or 6203?

Here is exactly what happened. Generator ran fine then just quit. I though maybe low oil shutoff. Nope. It is an overhead valve 10 hp Briggs and Stratton engine. It had thrown one of those push rods that runs the rocker arms that works the valves. The other rod was bent some. So I got two...

Looking for a single D carb adjusting tool, Chinese ok

Looking for a 261/262 magnesium clutch cover with working brake Mine is a 261 I assume they are interchangeable.

I need a good used husqvarna 261/262 cylinder that will clean up and a tank, alternatively a good used Husqvarna 55 or 254/257 tank (with the 254/257 AV buffers)

Sent an HDA 199 to Treemonkey for a mod for a Husky 359 I did a base gasket delete, muffler mod and porting, mostly matching lower transfers to base, widening and raising exhaust some. Slapped the modded carb on and put the saw back together. Never even touched the screws and 3 pulls later it...

See attached If someone can measure up the Stihl circlips and tell me if they have ears I will repost the chart with updated information Not all circlips are created equal and some AM pistons do not work well with OEM circlips.

I read were husqvarna modified the 550xp top cover to provide more ventilation and cooling. Can anyone post picture of the new and improved cover? Anybody ever use frog skinz on this cover to help with ventilation and if so, where do you put them so as not to interfere with the engineered air...

download and print a free degree wheel off the internet Cut it out and bring it to Office Max or another office supply store that does laminating Laminate it with their thickest laminate, cut the degree wheel out of the laminate leaving a border around the paper Laminate it again and cut it out...

go here https://www.k-bid.com/auction/18040

ok here is the problem, my H screw on the carb is one of those plastic things with the limiter wings. I got rid of the wings with the dremel but now the red plastic that surrounds the actual screw just sort of spins without adjusting the actual screw beneath it. Is there a fix for this short...

Someone posted that Mastermind wrote about a tank vent mod that would work on a husky 350 Can not find it, any help??

Replaced my broken down Husky 345 chain tensioner with one from EBay. It is a POS. What is the best, and I mean best, chain tensioner replacement for this. It is OK if it needs some modification to fit and work, I do not care if it comes from Stihl, China, Japan, Taiwan, Timbucktoo or Peru. ,

Dumb question # 1057 I cleaned the clutch needle bearings on the 345 I am rebuilding, after cleaning and oiling, the little needles rolled around Just figured out how to get to the clutch needle bearings on my trusty Stihl 025 Cleaned them and oiled them but the little needles are not moving...

I am rebuilding a 345 into a 346 with muffler mod and gasket delete, no porting. Am I short changing myself by using the 345 ignition coil? Would you recommend an unlimited coil and if so, which one from which vendor? How can you tell if the one being sold is unlimited? Lots for sale, non...

looking for a Husky 350 or variant riser

I bought an older rebuilt 044 several years ago. Today it gave up the ghost. The piston acts like the rod is broken or it is otherwise not connected to the crank, the piston will move freely in the cylinder, is not scored and looks good thru exhaust port. Seems these had bearing issues but I...

I know nothing about grinders. There seem to be some cheap and expensive ones that act like a chop saw, where the rotating wheel is dropped down unto the stationary cutter, like the cheap harbor freight model. Others where the rotating wheel is stationary and the cutters are moved into the...