What's on your bench?

[beaglebriar]

Doesn't look bad through the plug hole. The cylinder looks good, maybe a little bit of carbon scoring??

Lol they are pretty strong runners. How does the piston look?

 

[p61 western]

Doesn't look bad through the plug hole. The cylinder looks good, maybe a little bit of carbon scoring??

Unreal and you suck big time. lol

 

[Moparmyway]

 

[tickbitintn]

View attachment 121897

Flag holder??
Lol

Sent from my XT1635-01 using Tapatalk

 

[NCFarmboy]

4200 is strong happens to be my first saw. I bought in 1978. Still have it. Has bow bar 40hrs or less. Now shelf QUEEN.
Shep

 

[Bilge Rat]

Neighbor drug up a husky 365 in a basket.
Scored on the exhaust side. Piston is scored some. Lots of carbon,
just a coating on the piston and chamber. No big chunks missing to cause scoring.
The rim sprocket is almost in half so abuse may be a factor.

Why do people not clean their stuff before taking it apart?
How do you see anything wrong if everything is covered in crud?
Any why pull the cylinder then throw it all in a box for someone else to figure out.

It's only a Husky, how hard can it be!

 

[Lee H]

This is on my bench, Adirondackstihl broke it. He ran it last.

 

[Onan18]

This is on my bench, Adirondackstihl broke it. He ran it last.


View attachment 121972 View attachment 121973 View attachment 121974

Need a "Dislike" button for that one.

 

[usmcbuckwild]

This is on my bench, Adirondackstihl broke it. He ran it last.


View attachment 121972 View attachment 121973 View attachment 121974

Holy crap!!! Details?

I see the added counterweight broke off. Details on the reat of the saw is what I am requesting. Looks like an old Mac, 99/103 cc kart engine.

 

[Lee H]

101B Kart motor. Those are factory weights used on all the 123cc Mac's.
I was changing the rim and tapped on the crank to remove clutch. Then
went to start it and it was locked up. Never tap on one of those cranks.
I should have known cuz I did it once before.

 

[usmcbuckwild]

101B Kart motor. Those are factory weights used on all the 123cc Mac's.
I was changing the rim and tapped on the crank to remove clutch. Then
went to start it and it was locked up. Never tap on one of those cranks.
I should have known cuz I did it once before.

Very well! Note to self: don’t hit the crank on my 840.

That thing looks mean as hell. How does it cut?

 

[Lee H]

The 840 doesn't have those weights. This saw runs fantastic.

 

[MustangMike]

You can see the vids of it in the Upstate NY GTG section.

 

[stihl_head1982]

This is on my bench, Adirondackstihl broke it. He ran it last.


View attachment 121972 View attachment 121973 View attachment 121974

I'm not familiar with yellow saws, but that one would be one I'd like to run

 

[tickbitintn]

You can see the vids of it in the Upstate NY GTG section.

I have been avoiding that section because I really wanted to go.....

Sent from my XT1635-01 using Tapatalk

 

[tickbitintn]

I'm not familiar with yellow saws, but that one would be one I'd like to run

Ditto !!

Sent from my XT1635-01 using Tapatalk

 

[tickbitintn]

After work today I put a carb back on a pull-on p3816....
Blocked off the accelerator pump last night with some jb...
POS finally runs.... Well as good as it can...

I'll spare you from any pics !
( I didn't take any )

Sent from my XT1635-01 using Tapatalk

 

[Moparmyway]

Only had a few minutes, didn’t even take off the finish on the flat sheet

 

[Lee H]

I'm not familiar with yellow saws, but that one would be one I'd like to run

It's a fun saw to run and most want to run it but only a select few will.

 

[Woodrow]

It's a fun saw to run and most want to run it but only a select few will.

Lee, I am curious to know what kind of money does it take to build something like that? You don't have to answer that if you don't want to. I think that saw is badass and would love to build or have a saw built like that. Not sure I have the knowledge to build it would love to source the parts and maybe have it done.
Thanks, Dan