What's on your bench?

[Lightning Performance]

Finally getting around to putting a new handle on my ms201.


View attachment 103457

I love the way your shop looks. Wood walls, floors and bench. Going to copy it under a post and beam building at my home. All stained or washed/pickled wood inside. Maybe a steel wash down bench in the corner next to the parts wash cabinet. Milling will be my new best friend this year. Target wood will be hardwoods, large pine and red cedar.

Have a 2.1 poulan/husqy on the table losing a bar chain and sprocket to send norf. The bench is empty until a new one in a new spot is built. First of the year maybe. Five saws waiting and two to port. The Lucky Seven. 361 3.0 gets a spot.

 

[Moparmyway]

 

[Moparmyway]

@mikerudder

 

[czar800]

I love the way your shop looks. Wood walls, floors and bench. Going to copy it under a post and beam building at my home. All stained or washed/pickled wood inside. Maybe a steel wash down bench in the corner next to the parts wash cabinet. Milling will be my new best friend this year. Target wood will be hardwoods, large pine and red cedar.

Have a 2.1 poulan/husqy on the table losing a bar chain and sprocket to send norf. The bench is empty until a new one in a new spot is built. First of the year maybe. Five saws waiting and two to port. The Lucky Seven. 361 3.0 gets a spot.

Thanks, I’ve got it together!

 

[Mkinslow]

View attachment 103541 View attachment 103542 View attachment 103543 View attachment 103544 View attachment 103545

066???

 

[czar800]

The next saw I’ve been tinkering with today is that pioneer 1200. It’s running out of fuel in the cut… New fuel filter rebuilt the carburetor& carburetor was run through the ultrasonic cleaner. It’ll pulls good for maybe 5 to 10 seconds and act like it’s running out of fuel.


The carburetor seems to be adjusting properly And if you back off the trigger for a few seconds it’ll recover and cut fine for another 5 to 10 seconds. The thing is the RPMs don’t pick up like it’s trying to go to lean.

I’m just wondering if the fuel line in the tank is too small. Somebody had replaced it before I got the saw.

 

[Moparmyway]

066???

Yes Sir

 

[Moparmyway]

The next saw I’ve been tinkering with today is that pioneer 1200. It’s running out of fuel in the cut… New fuel filter rebuilt the carburetor& carburetor was run through the ultrasonic cleaner. It’ll pulls good for maybe 5 to 10 seconds and act like it’s running out of fuel.


The carburetor seems to be adjusting properly And if you back off the trigger for a few seconds it’ll recover and cut fine for another 5 to 10 seconds. The thing is the RPMs don’t pick up like it’s trying to go to lean.

I’m just wondering if the fuel line in the tank is too small. Somebody had replaced it before I got the saw.

Raise metering lever height

What is the popoff pressure ?

 

[Mkinslow]

Yes Sir

Thought I’d seen a rod bearing like that before

 

[czar800]

Raise metering lever height

What is the popoff pressure ?

It was 14ish

 

[beaglebriar]

It was 14ish

Fuel line could be collapsing Mike. What kinda tank vent does it have?

 

[Mattyo]

346xp....oe to NE conversion

 

[czar800]

Fuel line could be collapsing Mike. What kinda tank vent does it have?

It’s vented in the fuel cap, I’ve ruled out a vent Problem by running it with the cap loose.

 

[beaglebriar]

It’s vented in the fuel cap, I’ve ruled out a vent Problem by running it with the cap loose.

I'd replace the fuel line and filter then just to rule it out as well.

 

[Cut4fun]

Getting it ready for a collector.

This minus degree chit though is making it hard to get the barn shop warmed up in the mornings.

 

[460 magnum]

View attachment 102763 Getting closer to being a decent chain

Dang I just took a chain off that looked like this one.

 

[Dub11]

Getting it ready for a collector.

This minus degree chit though is making it hard to get the barn shop warmed up in the mornings.

View attachment 103659 View attachment 103660 View attachment 103661 View attachment 103662 View attachment 103663

It looks like your in a metal building like me. So I have one of these above the bench That one heat lamp helps tremendously while my gas and kerosene heater are warming up.

 

[Moparmyway]

346xp....oe to NE conversion

Hows she run ?

 

[Frank bierce]

Getting it ready for a collector.

This minus degree chit though is making it hard to get the barn shop warmed up in the mornings.

View attachment 103659 View attachment 103660 View attachment 103661 View attachment 103662 View attachment 103663

Niiice...the ole’ Tim Allen edition!!

 

[Frank bierce]

View attachment 103546 View attachment 103547 View attachment 103548 View attachment 103549 View attachment 103550
@mikerudder

Amazes me how much dirt and grime they can load up...