What's on your bench?

[a. palmer jr.]

Up next on my bench is a Stihl MS250 and a 290 to be rebuilt and a couple of 010 top handles to see if I can get to run. The 010s should be a chore since neither has a choke handle and I'm not sure where to look for one, maybe I'll save them for last.. By the way, ebay has one of those handles and are wanting around $48 for it! Think I'll pass...

 

[Onan18]

Torpedo Heaters.

 

[Czed]

View attachment 207630
Torpedo Heaters.

I have to smash those flat before the scrapyard will take them.

 

[bigbadbob]

Dun
One from 2
New seals bearings meteor
Welded up a cover on the muff as it was melting chain brake handle, only had silver VHT,,
Thin chit to weld,,,
Awaiting chicom chain brake/cover assy

 

[JohnnyBlade]

Up next on my bench is a Stihl MS250 and a 290 to be rebuilt and a couple of 010 top handles to see if I can get to run. The 010s should be a chore since neither has a choke handle and I'm not sure where to look for one, maybe I'll save them for last.. By the way, ebay has one of those handles and are wanting around $48 for it! Think I'll pass...

LOL! Is this what u need? I may have one, ill look tonite. Lol! If i do ill just send it to ya. I think that guy may have been under the influence of.......well everything under the kitchen cabinet when he posted that

 

[Ronie]

Dun
One from 2
New seals bearings meteor
Welded up a cover on the muff as it was melting chain brake handle, only had silver VHT,,
Thin chit to weld,,,
Awaiting chicom chain brake/cover assy
View attachment 207631 View attachment 207632

I hope you have better luck with the clutch covers than I did. I ordered three, one from CAL, one from NJ and one from China, all three turned out to be 61 covers. I got feed up and ordered oem covers.

 

[bigbadbob]

I hope you have better luck with the clutch covers than I did. I ordered three, one from CAL, one from NJ and one from China, all three turned out to be 61 covers. I got feed up and ordered oem covers.

I had good luck with a 394/5 cover,,, will see,,, ya just never know.

 

[Onan18]

I have to smash those flat before the scrapyard will take them.

Best Answer material right there!!!!!!!

 

[Backtroller]

View attachment 207630
Torpedo Heaters.

Come on, do you really need one in Georgia? 12 degrees this morning. Mine is still up on my shelf

 

[RI Chevy]

I doubt they are his. They are customers in for fixin.

 

[a. palmer jr.]

View attachment 207633 LOL! Is this what u need? I may have one, ill look tonite. Lol! If i do ill just send it to ya. I think that guy may have been under the influence of.......well everything under the kitchen cabinet when he posted that

These saws aren't mine but I imagine the guy who owns them would probably sell both of them for $48.. too bad the Chinese aren't making these or they would be about .48 apiece.

 

[JohnnyBlade]

These saws aren't mine but I imagine the guy who owns them would probably sell both of them for $48.. too bad the Chinese aren't making these or they would be about .48 apiece.

Lol! I was gonna say u could buy a whole
Saw for that price. Running. I sold one for $30 back in the summer thought i had a lever for ya but ive been digging and no dice. Sorry if i got ur hopes up.

 

[a. palmer jr.]

Lol! I was gonna say u could buy a whole
Saw for that price. Running. I sold one for $30 back in the summer thought i had a lever for ya but ive been digging and no dice. Sorry if i got ur hopes up.

No hopes, I found two more saws which didn't have levers on them either. There's a local guy that sells saws and parts that might have one but he recently passed away so I doubt that avenue is open. I'll keep the saws for a while and try to use something homemade to try to start one of them then give them back to owner...

 

[Mastermind]

What's on my bench?

Nuttin serious....

 

[PA Dan]

What's on my bench?

Nuttin serious....

View attachment 207740

Is that all...pfff

 

[Bigmac]

Ms461 broken tank and bent wrap!Was bent enough that the brake wouldn’t work! Lol

and fixed These guys are hard on stuff, so going to see if this full wrap holds up!

 

[Wolverine]

Kind of a bench.



Ick.


Call it good...

 

[av8or3]

This sparking plug took out this 365. I found the electrode stuck in the cyl head and managed to keep up with it until it fell thru my bench. Did not know exactly what it was for a while, looked like a small roll pin. Scratched my head for a day wondering about it and then I picked up the spark plug and really looked at it.
I’m rethinking NGK, much as I like them.

 

[huskyboy]

This sparking plug took out this 365. I found the electrode stuck in the cyl head and managed to keep up with it until it fell thru my bench. Did not know exactly what it was for a while, looked like a small roll pin. Scratched my head for a day wondering about it and then I picked up the spark plug and really looked at it.
I’m rethinking NGK, much as I like them. View attachment 208010View attachment 208011

Original plug? NGK is about the best for saws in my experiences, but nothing lasts forever or is bulletproof. I replace the plug on every newly acquired saw I get as preventative maintenance.

 

[av8or3]

Next up, whew!