TS420 Parts needed

[hseII]

We've got a Stihl TS420, & trying to decide the best path forward.

It needs:
1. Cylinder
2. Piston
3. Seals
4. Gasket Set
5. New lines

The Case will soon be split, & will determine if it's worth repairing based on the condition of the Crank.

Does anyone have the above itemS in useable condition they would part with?

Thank You.

 

[Adirondackstihl]

Will also need pulley from what I'm seeing.
Amongst other smalls.
But Heaths list will make a good start.

 

[hseII]

Will also need pulley from what I'm seeing.
Amongst other smalls.
But Heaths list will make a good start.

[emoji31][emoji31]

 

[Cobby08]

It needs to be man handled.... into the trash.

 

[hseII]

It needs to be man handled.... into the trash.

 

[Adirondackstihl]

It needs to be man handled.... into the trash.

^ this

 

[griffonks]

HL Supply new years sale...... buy new am ts420 chit. Usually used parts are trashed from sucking stone or concrete dust.

Don't forget the goofy bottom hose.... hi Jeremy, I been fishing.... Williams Fork river, Grand County Colorado. It's good dude, come on out...

Sent from my SM-G930T using Tapatalk

 

[griffonks]

My memory, the hls stuff is the bottom end. Crank, Cross bearings, seal and gasket kit.

The top end came from Farmertec/Huztl. This chit runs and lasts as good as oem squeal.

My favorite chop saw is the 272k hooskie. All that short stroke torque with a 52mm top-end but I traded my last one off for a mint pre-mtronic ms362.

So I bought a 371K but it's in my pile at Jimmys in NC. Like $140 for a nice one with a good p&c plus crank. He picked it up from the ebayer for me.

Until I get to the east coast I'm stuck with a MAC 10-10 chop saw, a ts760 boat anchor and a couple ts420's in a box.

The ts-420's are good for selling.... $5 to $600 for a nice one with Chinese guts..



Sent from my SM-G930T using Tapatalk

 

[Adirondackstihl]

Problem with the one(s) I got here, someone else dismantled them.
So in reality, I have no g-damn clue what's missing, what goes where or how they came apart.
I will say, that what I have here in boxes has been riden hard and put away wet.

The parts list that Heath originally posted is what I KNOW needs to be replaced. That doesn't include all the little small stuff like fuel hoses,air filter(s), primer bulb, deco valve, carb kit or complete carburetor etc....

I notice in one of your pictures Bill, that there is a Cross bearing "kit" with 3 bearings. I have no clue where that 3rd bearing goes.

Lastly, a local member @rb440 recently rebuilt a 420 for a relative. He used mostly all AM parts and has had nothing but issues. As a matter of fact, I believe the saw is still not running correctly.

 

[griffonks]

Call me, or call Jimmy. He can do one in a couple hours. If it's beat you will have to do the crankcase.

That spare bearing is just a 6202c3.

HLS sent me an oh44 crank instead of a ts420, I just noticed when I pulled it out.

If that case and covers are beat it's likely not worth the effort.

I see huztl is not selling topends on fleabay now. Jimmy gets his Chinese parts from DD....



Sent from my SM-G930T using Tapatalk

 

[Adirondackstihl]

Tank assy #1

 

[Adirondackstihl]

Tank assy #2

 

[Adirondackstihl]

This is the builder case with builder crank.
I hope the threads are cleanable.

 

[Adirondackstihl]

Box O Parts

 

[Adirondackstihl]

Best method to remove baked on concrete?

 

[huskihl]

Best method to remove baked on concrete?
View attachment 72242 View attachment 72245

What a Mongolian clusterphuuuuu k. I was thinking of upgrading my 400 to a 420........

 

[huskihl]

Best method to remove baked on concrete?
View attachment 72242 View attachment 72245

Muriatic acid eats concrete. Also Mg, Al.

 

[Onan18]

Best method to remove baked on concrete?
View attachment 72242 View attachment 72245

Jeremy believe it or not a pressure washer works really well. For small parts like carbs might want to try an USC.

 

[Adirondackstihl]

What a Mongolian clusterphuuuuu k. I was thinking of upgrading my 400 to a 420........

You do know a 420 is a strato Saw right?

 

[huskihl]

You do know a 420 is a strato Saw right?

Yes