So what did you buy today

[Partner]

A few things for $25 / Proxon $100 torque wrench new 3/8" 20-100Nm, Gedore Key Piece $40, $30 wedge

 

[Partner]

Today's puzzle / 2" shaft is broken

Looks like a takedown wedge?The only thing missing is this ring

Klin aluminiowy kuty 980g

Ciężar 980 g. Odkuwany, w komplecie z drewnianym trzonkiem i pierścieniem.

e-pilarz.com

 

[Bill G]

I was going to build one and decided to look online for some ideas and found it on eBay. I figured I couldn’t build it for what I could buy it for and at worst I’d have the levers and pins for the skid steer side to use if it turned out to be junk. It held up really well and I’d buy it again in a heartbeat. Not too often you get some cheap Chinese thing on eBay and it turns out to be very well built like this thing is.

3 Point 3 Pt Skid Steer Quick Tach Conversion Adapter Fit For Cat 1 Tractor US | eBay

3 Point Skid Steer Quick Tach Conversion Adapter Fit For 3 Pt Cat 1 Tractor 2200lbs Capacity. kid steer 3 point adapter is made from stainless steel and covered with powder coating for rust and corrosion resistance.

www.ebay.com

I have a wild idea to try to adapt a skid loader mount for the loader on a old highway tractor I have. It is a freeman loader on it with a rock bucket that is pinned mount, I have a much better bucket off a larger Bush Hog loader that has the skid loader mount. Are there different sizes of skid loader mounts. All I have ever had is pinned on buckets for the skid loader

 

[Partner]

In my life I have never seen such an engine 10$

 

[jblnut]

New set of diggers for the skiddy. I went in to pay for them and told the yard guy to toss them in the minivan outside. He didn't want to at first and I told him It's a Town and Country and I flipped the switch on the dash to Country so it'll be fine. He said Okay and they were inside when I got back to the van

 

[president]

This walked into the shop this afternoon, it's mine now.

View attachment 441793

The home made handle fell off when he started the saw to show me that it would run...we have a suitable used one coming off eBay.

View attachment 441794

7 digit serial number which I understand (from another post) makes it a fairly early one.

View attachment 441795

Just what I needed, another project...

Mark

Donny Walker ,Walkers saw shop, said they used those foe big timber falling on
the west coast , with the 2100 huskies! tourque by the bucket loads

 

[ammoaddict]

Got this dukes bar and chain.

 

[jblnut]

Look at this cute little saw I got in the mail from @Lone Wolf !!


Definitely impressed so far. What a little screamer this thing is !! I think it has the potential to become one of my most used saws.

 

[LAWN BOY]

Look at this cute little saw I got in the mail from @Lone Wolf !!
View attachment 442256

Definitely impressed so far. What a little screamer this thing is !! I think it has the potential to become one of my most used saws.
View attachment 442257

Nice, I seldom see those rear handle 200s.

 

[Joe M]

I have a wild idea to try to adapt a skid loader mount for the loader on an old highway tractor I have. It is a freeman loader on it with a rock bucket that is pinned mount, I have a much better bucket off a larger Bush Hog loader that has the skid loader mount. Are there different sizes of skid loader mounts. All I have ever had is pinned on buckets for the skid loader

There’s a mini and a standard size skid steer mount. The standard is the most common, there might be an oddball type out there but I think it’s pretty standardized

 

[Wonkydonkey]

Dammit. I blame you lot,,,,,lot.damit m-fuks

 

[Bill G]

There’s a mini and a standard size skid steer mount. The standard is the most common, there might be an oddball type out there but I think it’s pretty standardized

I take it this is the mini

3 Point 3 Pt Skid Steer Quick Tach Conversion Adapter Fit For Cat 1 Tractor US | eBay

3 Point Skid Steer Quick Tach Conversion Adapter Fit For 3 Pt Cat 1 Tractor 2200lbs Capacity. kid steer 3 point adapter is made from stainless steel and covered with powder coating for rust and corrosion resistance.

www.ebay.com

 

[whitesnake]

New set of diggers for the skiddy. I went in to pay for them and told the yard guy to toss them in the minivan outside. He didn't want to at first and I told him It's a Town and Country and I flipped the switch on the dash to Country so it'll be fine. He said Okay and they were inside when I got back to the van
View attachment 442216

Gotta love vans and wagons! Luckily you remembered to put it in country mode.

 

[jblnut]

I take it this is the mini

3 Point 3 Pt Skid Steer Quick Tach Conversion Adapter Fit For Cat 1 Tractor US | eBay

3 Point Skid Steer Quick Tach Conversion Adapter Fit For 3 Pt Cat 1 Tractor 2200lbs Capacity. kid steer 3 point adapter is made from stainless steel and covered with powder coating for rust and corrosion resistance.

www.ebay.com

Nope. That is the full size skid steer side. It’s a Category 1 3pt at best. I’m not worried about destroying it with my 2038r but anything larger and I think it’d fold up. Depends on what you’d be doing with it I guess.

The mini skid steer mount is common on the smaller wall behind toro and bobcat tracked skid steers. No modern skid steer has the mini mount that I’m aware of.

 

[Bill G]

Nope. That is the full size skid steer side. It’s a Category 1 3pt at best. I’m not worried about destroying it with my 2038r but anything larger and I think it’d fold up. Depends on what you’d be doing with it I guess.

The mini skid steer mount is common on the smaller wall behind toro and bobcat tracked skid steers. No modern skid steer has the mini mount that I’m aware of.

The Cat 1 issue for me is not a worry. I just want to make sure it will match the 8 foot bucket off the big loader.

I am redneck engineering this deal and just want to make sure I do not buy something that will not match the bucket

 

[bradb123]

I bought this yesterday. I'm looking forward to seeing how it cuts later today.

 

[Squareground3691]

I bought this yesterday. I'm looking forward to seeing how it cuts later today.

Got a couple of 18” loops awhile ago, it works well, but the 23RS Pro is faster, it’s a very nice chain thoe ,

 

[Partner]

The file will tell you what material it is, I think I have one too. But semi chiesel sp33g

 

[justoldsaws]

Visited a retired softwood logger today.
Came home with a 044 and 076, heaps of bar sprockets, clutch drums for 084 and 064 and 044 parts.
Also lots of rubber av mounts for 084.

 

[heimannm]

That is a nice mess of stuff there justoldsaws, now you have to figure out how to organize it so you can find the pieces you need when you need them...

...this is part of a haul I made a few years ago...



I still don't have everything put where I can find it.

Mark