Saw video thread

[Backtroller]

Impressive videos Al.

 

[Keith Gandy]

Impressive videos Al.

Ya the 036 is nice

 

[jmssaws]

Where do u like the rakers on 70+ cc saws?

030? Maybe 040 depends on what I'm doing.

 

[Keith Gandy]

030? Maybe 040 depends on what I'm doing.

Pretty low ? Ive been about .020 to .025

 

[jmssaws]

040 for play and 020 for work.

 

[Keith Gandy]

Ive tried 050 and with a 390 almost yanked the saw outta my hand!!!!

 

[drf256]

Ya the 036 is nice

Thanks guys.

I dont know how to multiquote here.

That one has .054 from the band, the piston free ports the ex floor at tdc, .025 squish.

It also has upsloping uppers. 119 @ the intake and 122 @the exhaust side.

 

[mdavlee]

Thanks guys.

I dont know how to multiquote here.

That one has .054 from the band, the piston free ports the ex floor at tdc, .025 squish.

It also has upsloping uppers. 119 @ the intake and 122 @the exhaust side.

How do you like the exhaust side opening first?

 

[drf256]

The intake opens first.

Not sure how much difference it makes. I'd have to test it side by side.

Backtroller's open at 120 even. If he wants, I'll raise the intake to 118. But, he's looking for reliable cutting and not a race.

Anyone here think that the factory opens assymetrically for ease on the rings sliding across them and not for performance???

 

[mdavlee]

The intake opens first.

Not sure how much difference it makes. I'd have to test it side by side.

Backtroller's open at 120 even. If he wants, I'll raise the intake to 118. But, he's looking for reliable cutting and not a race.

Anyone here think that the factory opens assymetrically for ease on the rings sliding across them and not for performance???

I was thinking backwards this morning. They could be doing that on those wider transfers like the stihls.

 

[Backtroller]

120 is fine with me. You are correct I'm not looking for a race saw, however it's going to run really good by the look of things.

 

[drf256]

What kind of recipe # is in this bad boy?

104/119.5/72

.058 from the band. Around 225psi after 2 tanks right now.

No bridges

 

[Mastermind]

Al's saws are looking damn good this morning.

 

[Deets066]

Al's saws are looking damn good this morning.

Yes they are! A lot of people over looked him on AS

 

[Mastermind]

I spent a lot of years there.

Thank God we have this place now.

 

[Deets066]

He's my old man runnin my hybrid the first day I got it together, it was really fat in this video, only was turnin 12,500 unloaded

 

[drf256]

Very impressive saws here, if I do say so myself.

I have very limited saw experience, but I can even tell what's fast anymore.

Anyone have a stock vs. ported video?

I'm hoping (time, weather and videographer permitting) to do a stock 026/036 and ported with the same bar and chain in the same wood at some point on my next two builds.

Pat,
Did you happen to do a video of your 034 cutting before you pulled it apart?

Would be fun to see the difference.

 

[Backtroller]

I did have some older ones. I just had my phone replaced and am having some technical issues with iCould. A few Christmas ones are AWOL too.

 

[Redfin]

Very impressive saws here, if I do say so myself.

I have very limited saw experience, but I can even tell what's fast anymore.

Anyone have a stock vs. ported video?

I'm hoping (time, weather and videographer permitting) to do a stock 026/036 and ported with the same bar and chain in the same wood at some point on my next two builds.

Pat,
Did you happen to do a video of your 034 cutting before you pulled it apart?

Would be fun to see the difference.

Stock 12mm. 446 ported hybrid.

 

[drf256]

Your bar's on upside down.