High Quality Chainsaw Bars Husqvarna Toys Hockfire Saws

Oilier adjustment for Lite Bars

redneckhillbilly

Pinnacle OPE Member
Yearly GoldMember
Local time
9:54 AM
User ID
23623
Joined
May 30, 2022
Messages
433
Reaction score
1,235
Location
NW MT
Country flag
Just had a question after running my 592 with Husqvarna Lite Bar, the only saw with a Lite Bar I have ever ran, do the Lite Bars require a different amount of oil due to the difference in materials? I have the oiler turned up almost all the way and I dont really see the oil in the chain as much as I can with a standard bar, I know I know I am overthinking this, but what do others do? give them less oil, or more oil?
 

ammoaddict

Here For The Long Haul!
Local time
11:54 AM
User ID
4713
Joined
Nov 29, 2017
Messages
2,386
Reaction score
10,345
Location
Granite Falls, NC
Country flag
Just had a question after running my 592 with Husqvarna Lite Bar, the only saw with a Lite Bar I have ever ran, do the Lite Bars require a different amount of oil due to the difference in materials? I have the oiler turned up almost all the way and I dont really see the oil in the chain as much as I can with a standard bar, I know I know I am overthinking this, but what do others do? give them less oil, or more oil?
Check the oil holes in the bar. My guess is the older bar has bigger holes.
 

redneckhillbilly

Pinnacle OPE Member
Yearly GoldMember
Local time
9:54 AM
User ID
23623
Joined
May 30, 2022
Messages
433
Reaction score
1,235
Location
NW MT
Country flag
the saw goes through oil, and I can tell the chain is oiling, but its harder to see it, maybe its just the stainless color of the bar that hides the oil better, I was wondering if by design they require a different adjustment than a standard bar, but it doesnt sound like that is the case.
 

Wilhelm

I'm here for the sick'n twisted company
Yearly GoldMember
Local time
5:54 PM
User ID
1204
Joined
Apr 28, 2016
Messages
13,801
Reaction score
54,306
Location
Croatia
Country flag

dangerousatom

Super OPE Member
Local time
11:54 AM
User ID
11828
Joined
Feb 25, 2020
Messages
197
Reaction score
484
Location
Quakertown, PA, United States
Country flag
If you dont think ur getting enough oil during a cutting session but there is no sign of it ( burnt bar or excessive heat, wood sap gumming in the chain bits ) Try making a few long cuts and then quickly shutting down with no extra revs or throttle blips out of the cut. Take a new clean paper towel, tissue, even copier paper and and grab the bottom of the bar n chain and see it there is any evidence of oil on it.

It doesnt take much more then thin film of oil to keep things sliding right, its just a matter of keeping a continuous film going. If your familiar with your saw your eyes and nose will usually tell you there's and issue before the saw or your chips.
 

hacskaroly

2100 Fanclub Member
Yearly GoldMember
Local time
8:54 AM
User ID
27954
Joined
Nov 24, 2023
Messages
1,802
Reaction score
6,056
Location
Northern Idaho, Ehh
Country flag
I was wondering if by design they require a different adjustment than a standard bar
No, they don't require any different oiling adjustment than standard bars, just the type of wood being cut and size bar you are using (obviously, the longer the bar more oil you will need to get around the bar).
 

dangerousatom

Super OPE Member
Local time
11:54 AM
User ID
11828
Joined
Feb 25, 2020
Messages
197
Reaction score
484
Location
Quakertown, PA, United States
Country flag
Im actually surprised nobody makes a high end steel bar with replaceable nose that is full hollow center with a single wall of 16g titanium thats punched and then vacuum brazed to the outer steel. It be stupid expensive :crazylick: ( $350 for a 24" Id wager ) but it would likely weigh less then 1/3 of a full steel bar.

Thinking about it, there may be thermal issues with such a small amount of steel and warping or long term heat cycle vs temper issues
 
Top