Not so pros 4 new and without politics or drama

[redline4]

Drift on the deck is at 30"

 

[SawAddictedFarmer]

Good afternoon. @redline4 I think you need to go visit @Kiwioilboiler, he's hogging all the heat!

 

[redline4]

Good afternoon. @redline4 I think you need to go visit @Kiwioilboiler, he's hogging all the heat!

I blame Adam for global warming.
Seems logical anyway.

 

[Stump Shot]

I blame Adam for global warming.
Seems logical anyway.

Well, it came from @GCJenks204 way.

 

[Tor R]

Chainsaw carburetor question for you Gurus, inlet valve, wasn't there a con tool to make a new seat (from older hda times)?

I'm working on carburetor tools..

 

[Tor R]

Good morning guys,
figured out what part number for HDA,
Walbro 500-502 or Husqvarna 5310302-42

The new Walbro kit 500-538 do not have this part in the kit

 

[Junk Meister]

Chainsaw carburetor question for you Gurus, inlet valve, wasn't there a con tool to make a new seat (from older hda times)?

I'm working on carburetor tools..

Good morning guys,
figured out what part number for HDA,
Walbro 500-502 or Husqvarna 5310302-42

The new Walbro kit 500-538 do not have this part in the kit

Deer in the Headlights if I looked in a mirror. Mebbe if i wait ya'll out a picture will appear of said tool.

 

[Wonkydonkey]

Good morning snowdrifters

Err today, I think I’ll be coughing & coughing some moar …with the occasional blowing some snot out

 

[Stump Shot]

@Tor R
As far as carburetor tools go, I use the Zama kit 750-200 much more, on all carburetors, not just Zama's.

 

[Tor R]

@Tor R
As far as carburetor tools go, I use the Zama kit 750-200 much more, on all carburetors, not just Zama's.

I looked at it now, but not what I'm looking for.
I would like to have tools we use to work inside the carburetor, such as if we need to make a new needle valve seat.
Actually also several impact tools for x types of welch plugs.

 

[Lawless]

Weather today could be rough

 

[redline4]

Owner of the dealership texted me, said we are opening late and get there whenever if we even feel we can come in.
Got another 6-7" happening today and it's switched to the light snow so the 25mph steady wind is piling it up.
Lots of big companies are closed it looks like.

 

[ray benson]

Good morning. 1 1/2" rain last night and snowing now. 28°F/ -2°C and that is the high. Dropping to 15°F/ -9°C by midnight. Snow total should only be about an inch.

 

[Tor R]

I got a batch tool today:

 

[GCJenks204]

Good Morning All!! Just another frickin Monday...

Well, it came from @GCJenks204 way.

Can't blame me for this, came from @maulhead out of Colorado as best as I can tell. The snow didn't cross the border, got kept South by a blast of cold air -13F this morning...

 

[Stump Shot]

I looked at it now, but not what I'm looking for.
I would like to have tools we use to work inside the carburetor, such as if we need to make a new needle valve seat.
Actually also several impact tools for x types of welch plugs.

It makes doing all those jobs easier.

 

[Stump Shot]

Good Morning All!! Just another frickin Monday...

Can't blame me for this, came from @maulhead out of Colorado as best as I can tell. The snow didn't cross the border, got kept South by a blast of cold air -13F this morning...

So, the arctic blast came from Brazil?

 

[SawAddictedFarmer]

Good morning. It's snowing here but nothing dramatic, we had nasty winds and tornado watch last night but no damage here.

 

[Stump Shot]

Good morning. 14F snowing and blowing.
Maybe 16 to 18 inches so far and counting...

 

[nbbt]

Morning folks, started the day at +8f, sunny now, about 20f later before bropping below 0f for the overnight.

Snow total from Saturday's spritzing ended up at 14" of stuffs that was not fluffy.