Not So Pro 3

[Mastermind]

The surgeon just called me and said Donna is out of surgery and he said it went very well

I’m just waiting to see her in recovery

Thanks again everyone

That's great to hear Michael.

 

[Mastermind]

We are experiencing mudageddon here on the plateau. I just spread 27,360 lbs of 3/4" stone on my granddaughter's driveway....

 

[dall]

We are experiencing mudageddon here on the plateau. I just spread 27,360 lbs of 3/4" stone on my granddaughter's driveway....

pictures or it didnt happen

 

[Mastermind]

pictures or it didnt happen

Tomorrow if I remember. I had to pull Austin out of the driveway this morning so he could get to work.....that's how bad it was.

 

[Loony661]

View attachment 406028
Found the wiggle in my center bushings: lower one has a cracked housing, and play between the sphere and the race. Pin was also just slightly stepped. Upper was good, but I’m putting in both pins and bushings.
View attachment 406029
Off to the parts house now for all the shiny stuff!

So I was wrong about that crack - it’s manufactured that way so that the sphere can be installed. Makes sense now that it was explained to me. Anyway, got new pins and bushings. After cleaning up and measuring the bronze shims, I’ll need those as well, and whoever did this job last time, didn’t use enough shim on the bottom section, which is probably where a lot the felt wiggle was coming from.

 

[beaglebriar]

Evening fellers. Piston is back in the YZed. We’ll probably get it buttoned up tomorrow night so the kid can test rip it down the ice covered driveway…

 

[full chizel]

Evening fellers. Piston is back in the YZed. We’ll probably get it buttoned up tomorrow night so the kid can test rip it down the ice covered driveway…

Sheet metal screws in the tires and just send it

I used Kold Kutter traction screws on ice.

 

[Woodslasher]

Have a super sparkley gear lube days bishes

View attachment 405993View attachment 405994View attachment 405995

Reminds me of the 1st time I dropped the diff cover on the Dodge:

 

[beaglebriar]

Sheet metal screws in the tires and just send it

He’d like a set of Trelleborg’s but sheet metal screws are more in his budget. Lol

 

[full chizel]

He’d like a set of Trelleborg’s but sheet metal screws are more in his budget. Lol

Yeah about $350 a tire. Kold Kutter screws are fairly cheap and work real good. Amazon even sells them.

 

[Only the Tony]

Tomorrow if I remember. I had to pull Austin out of the driveway this morning so he could get to work.....that's how bad it was.

Last week we had that going. Ground was thawing with the rains we were getting and you couldn't go anywhere in the backyard. Hooked up the hay trailer and that was enough to stop any motion even with 4 wheel drive.

 

[Loony661]

View attachment 406109
Last week we had that going. Ground was thawing with the rains we were getting and you couldn't go anywhere in the backyard. Hooked up the hay trailer and that was enough to stop any motion even with 4 wheel drive.

I lost traction in the mud the day before yesterday. Frost is coming out and the top 3-4” is just mud.

 

[Kiwioilboiler]

View attachment 406051

OMG Dallas, that engine hoist looks exactly like



an engine hoist.
Thank you so much for asking Ed to publish pics of it. My life is now complete.

 

[John Wargo]

Evening fellers. Piston is back in the YZed. We’ll probably get it buttoned up tomorrow night so the kid can test rip it down the ice covered driveway…

Short sheet metal screws in the knobbies or a set of Trellborgs will fix a icy driveway for aspiring dirt bikers

 

[John Wargo]

Drywall and metal framing test this morning. Any of you ladies stopping by?

 

[Lnk]

Drywall and metal framing test this morning. Any of you ladies stopping by?

Remember the 5/8", or was it commie 16mm?

 

[Lnk]

Good morning men, once again heading to the plateau, seems Randy keeps breaking stuff over there. Supposed to hit 60 here today. Be safe all.

 

[John Wargo]

Remember the 5/8", or was it commie 16mm?

We definitely have talked about that

 

[GCJenks204]

Morning / Evening All. -1C/30f this morning, a little cooler but still pretty incredible for Feb 1.

 

[stihl livin]

Morning men and users of sandpaper sexual products. Another day of doing the Dallas here. Wish me luck