Not So Pro 3

[Mastermind]

hiccups or been watching too much pa porn ?

Damn junky ass forum.

Why notches instead of drilling a couple of holes in the rod end? I have opinion either way, just curious if one is better/easier than the other.

I've thought about drilling a hole, but I think a notch on each side would be easier to do, and deburr well enough to be sure the bearing holds up.

 

[P.M.P.]

 

[Boomhower]

View attachment 264441

Those r funny lookin catfish


Sent from my iPhone using Tapatalk

 

[dall]

Damn junky ass forum.



I've thought about drilling a hole, but I think a notch on each side would be easier to do, and deburr well enough to be sure the bearing holds up.

the brass pieces ride on the bearing or the wrist pin ?

 

[Mastermind]

the brass pieces ride on the bearing or the wrist pin ?

On the bearing, but just the ends where the needles stop. The first set I made fit up onto the needles, but since they stop short of the end, I was afraid they would be too loose. I'll try to get more pictures tomorrow to better explain.

 

[dall]

On the bearing, but just the ends where the needles stop. The first set I made fit up onto the needles, but since they stop short of the end, I was afraid they would be too loose. I'll try to get more pictures tomorrow to better explain.

i understand what you are saying
so it would be better to groove the crank because if you groove the bushing it could possibly snag on the bearing if something started to fail

 

[Stihl working Hard]

Good morning guy'sView attachment 264323

That’s excellent Dave lmao

 

[Stihl working Hard]

Bruh, your hitch is draggin yo.

View attachment 264338

The decal in the LH rear window says it all

 

[Stihl working Hard]

A friend in western Iowa sent me this pic.

Yes, it has purple wheels.
View attachment 264339

@stihl livin , might give you some ideas for your ride.

Looks Ghay

 

[Stihl working Hard]

Sup mfers?

Check out this madness.

View attachment 264414

Looks pricey spacers on the crank ,nice work is that all your doing Randy

 

[Stihl working Hard]

Errr....394 piston actually.

Belongs to Cobby.

How you like those brass spacers to keep the rod centered in the piston?

Nice work buddy are there any distinct advantages to the adding the 394 piston

 

[Stihl working Hard]

Good morning OPE hope everyone has a great humpday today

 

[Stihl working Hard]

hiccups or been watching too much pa porn ?

Lmao my money is on the porn

 

[Stihl working Hard]

On the bearing, but just the ends where the needles stop. The first set I made fit up onto the needles, but since they stop short of the end, I was afraid they would be too loose. I'll try to get more pictures tomorrow to better explain.

Iam looking forward to the stroker 661 thread

 

[Stihl working Hard]

View attachment 264441

Are you having these for dinner Gunner

 

[cuinrearview]

Good morning OPE hope everyone has a great humpday today View attachment 264462

Ain't this the truth. Good afternoon how's Todd?

 

[Stihl working Hard]

Ain't this the truth. Good afternoon how's Todd?

Doing ok thanks Tim can’t complain work is slowly picking up not going to be extremely busy until the houses get more advanced

 

[GCJenks204]

Morning All. A chilly 18 for our walk this morning. Strong south west wind blowing in some warm air though. Supposed to be above freezing by this afternoon and then the rest of the week.

 

[Stump Shot]

Good morning hackie-slacks.
Still the frozen tundra here.

 

[ayoungtexan]

Good morning fellas