Not So Pro 3

[Stihl working Hard]

Should we start a gofundme for his bail or let him stick it out a while?

LMFAO Joe Iam going to watch the news here tonight to see if dall is the leading story

 

[Stihl working Hard]

I sawed my thumb off with a circular saw. Believe it or not, it hurt like a mfer.

No sh!t did they sew it back on stumpy

 

[huskihl]

Why tf were they showing you that stuff in high school?

Kids were different then. They didn’t run home to mom crying about the emotional distress they experienced in shop class. This was before they tried fixing stupid

 

[Nighthunter]

Morning, been a while since I posted on here, how's everyone doing,local dealer is now selling these, looks really well made

 

[Egg Shooter]

Apparently, Mike Finnegan is from somewhere here in GA.
Watched him do a few runs at a track somewhere in Cherokee county and a drag boat segment, maybe on lake Lanier or Oconee.

That boat is bad a$$. So is his hemi gasser.

 

[Egg Shooter]

Ever see the ones of the dudes who got pulled into lathes?

A guy at a place I worked at was wearing a loose and open flannel shirt over his T-shirt up on the table of a big a$$ cnc boring mill making holes in hoist frames. He got sucked in. They figure the only reason he survived was his strength fighting it because he "only" ended up with 8 broken ribs and lots of bruising. He was shirtless when he was able to get back from it. After that they installed a pressure sensor rubber "floor" around it so if he stepped on it it killed the machine.

 

[ayoungtexan]

Good morning fellas. Hope y’all have a great Monday

 

[GCJenks204]

Morning all.

A chilly 48F to start the morning, almost needed to put on pants for our morning walk.

Have a safe Monday.

 

[Woodpecker]

Morning, been a while since I posted on here, how's everyone doing,View attachment 256780local dealer is now selling these, looks really well made

Chain stretcher?


Morning everyone.

 

[P.M.P.]

Mornin coffee is good

 

[Nighthunter]

Chain stretcher?


Morning everyone.

chain holder for sharpening chains

 

[dall]

How so?

lol see Kevin’s answer




Damn slackers

 

[P.M.P.]

chain holder for sharpening chains

I could use one of these.

 

[dall]

I could use one of these.

probably too big for the 10 inch bars you run on your huskies

 

[Nighthunter]

If your interested, I can get you one

I could use one of these.

 

[P.M.P.]

If your interested, I can get you one

I just seen the price tag 125.00 little more than I want to spend.

 

[redline4]

A guy at a place I worked at was wearing a loose and open flannel shirt over his T-shirt up on the table of a big a$$ cnc boring mill making holes in hoist frames. He got sucked in. They figure the only reason he survived was his strength fighting it because he "only" ended up with 8 broken ribs and lots of bruising. He was shirtless when he was able to get back from it. After that they installed a pressure sensor rubber "floor" around it so if he stepped on it it killed the machine.

Its amazing how quick things can go wrong.
Probably 15 years ago now I finished up a front cover gasket on a Buick 3.8.
Had it running and dropped something. When I reached for it the belt grabbed my hand, pulled it around until it was jammed up agsinst the engine mount, the crank pulley chewing on 1 side of my digits, the serpentine belt gnawing on the other side. I had no choice but to pull straight out.
Burgered up my digits pretty good, but I still have them.

 

[dall]

Its amazing how quick things can go wrong.
Probably 15 years ago now I finished up a front cover gasket on a Buick 3.8.
Had it running and dropped something. When I reached for it the belt grabbed my hand, pulled it around until it was jammed up agsinst the engine mount, the crank pulley chewing on 1 side of my digits, the serpentine belt gnawing on the other side. I had no choice but to pull straight out.
Burgered up my digits pretty good, but I still have them.

Pictures

 

[Mastermind]

No sh!t did they sew it back on stumpy

Yep....but now it doesn’t bend. Lost about 10mm in length too. The saw was on a 45 degree angle, and it cut thru the joint. Looking back now, I should have had it removed rather than reattached.

Morning, been a while since I posted on here, how's everyone doing,View attachment 256780local dealer is now selling these, looks really well made

Good morning Oisin. Good to see you around my friend.

 

[redline4]

Pictures

I dont keep pictures of Buicks.
Slacker.