Not So Pro 3

[dall]

Burp !!!

your gonna need bigger bibs

 

[Stump Shot]

I'm gonna rebuilded the old 10 horse over time. Im just slow. Like special kid window licker slow lol

Is it a Kohler?

 

[Agent Smith]

Is it a Kohler?

You betcha

 

[dall]

Is it a Kohler?

should be a old k motor 301?

 

[dall]

k241 i was wrong

 

[Stump Shot]

You betcha

Doubt it needs much, those old motors were tough.

 

[Agent Smith]

should be a old k motor 301?

K 241 son

 

[Agent Smith]

Doubt it needs much, those old motors were tough.

Until they need machined which this one does. I don't have the equip to do the machining so $500 in machining and $400 in parts= why im going harbor junk motor till I get the kohler 10 horse going again

 

[dall]

K 241 son

I looked it up and corrected myself

 

[Czed]

Well...this 64-gun hernia mf’r was put in place about mid-afternoon. 650lbs felt exactly like...650lbs. Had no choice but to put it in place in the living room where the solid oak/glass door gun cabinet was...too wide from left to right to even think about negotiating the hallway to get it into one of the three bdrms. Is what it is, but I knew it going into the purchase. *f-wordk ‘em, feed ‘em fish heads if don’t nobody like it in the living room, what I say.

View attachment 270366
View attachment 270367

Put a blanket over it
Nobody will know.

 

[Agent Smith]

Another one of my favorite builds

 

[Stihl working Hard]

Sounds fun and good luck to them, what is netball?

Sort of similar to basketball except non contact and stand and throw no dribbling period

 

[Stihl working Hard]

Hi Todd! Enjoy your weekend buddy!

Thanks Dan the same to you my friend

 

[Stihl working Hard]

im ok coffee time then work on junk

Then a little slacking

 

[Stihl working Hard]

I'm so going to do that tomorrow morning at Home Depot. They have canned fuel right there. Lets see if they disabled that floor model

Evening Todd

I want to see pics of you getting pulled outa the store or mug shots at the police department

 

[Stihl working Hard]

Howdy Todd. Starting to install laminate wall panels on z clips.

That sounds like fun

 

[Stihl working Hard]

#Whateverthefuckthismeans

View attachment 270291

I interpreted it as there’s a squeak in the front brakes when I weave all over the road at slow speeds like an idiot

 

[Stihl working Hard]

Before and after. This mfer is done. On to the next customer


View attachment 270317 View attachment 270318 View attachment 270319 View attachment 270320

Looks awesome great job

 

[Stihl working Hard]

Well...this 64-gun hernia mf’r was put in place about mid-afternoon. 650lbs felt exactly like...650lbs. Had no choice but to put it in place in the living room where the solid oak/glass door gun cabinet was...too wide from left to right to even think about negotiating the hallway to get it into one of the three bdrms. Is what it is, but I knew it going into the purchase. *f-wordk ‘em, feed ‘em fish heads if don’t nobody like it in the living room, what I say.

View attachment 270366
View attachment 270367

Are you sure that not stolen from Fort Knox that’s a bad looking mfer

 

[Stihl working Hard]

Any pics of the wet noodle trick?

P.S. Same can be said for the motors in my opinion. Rather revive an oldie if possible. But that's just me, I like listening to the old ones run.

Lmao