044

[Canadian farm boy]

The X before the SN is just a mark the factory uses to indicate that the saw was tested. Later saws like the MS series will have an X at the end of the SN.


Serial #12938283 was the switch from 10-12 mm cranks

 

[Stump Shot]

That’s what I was thinking. But the crank case is 12mm

just saying…….
So was there ever a red lever 12mm … it was a porn shop sale

I just finished up a 12mm red lever 044.
Where did you get this thing @Woodrow , you pimpin saws in porn shops now???

 

[Wonkydonkey]

The X before the SN is just a mark the factory uses to indicate that the saw was tested. Later saws like the MS series will have an X at the end of the SN.


Serial #12938283 was the switch from 10-12 mm cranks

That’s what I said a in my post #30 earlier , I know you understand
But does everyone else especially old redeye

044

Btw thanks Steve, for the info I didn’t know about he 12mm 044 red leaver

 

[Gary Courtney]

Picked up another one.

 

[farminkarman]

View attachment 330400Picked up another one. View attachment 330401

Kinda wish I could find one of these things.

 

[Gary Courtney]

Kinda wish I could find one of these things.

The cylinder was not in the box! Now I need a 10mm slant cylinder

 

[farminkarman]

The cylinder was not in the box! Now I need a 10mm slant cylinder

That’s a bummer. I would bet someone on here has one stashed away.

 

[huskihl]

The cylinder was not in the box! Now I need a 10mm slant cylinder

You’re a little bit too late. A couple years ago I had six of them

 

[jacob j.]

You’re a little bit too late. A couple years ago I had six of them

Did you make them into beer bottle cubbies for friends and family?

 

[huskihl]

Did you make them into beer bottle cubbies for friends and family?

Ashtrays

 

[farminkarman]

Would this work?

 

[Gary Courtney]

Would this work? View attachment 330413

i saw that. would like to see inside

 

[farminkarman]

i saw that. would like to see inside

I think that would be a fair ask of the seller. That is a lot of money to spend without knowing the condition of the cylinder.

 

[Gary Courtney]

 

[MustangMike]

Very nice! Has a 440 tank holder, but the nice early air filter cover (which I prefer).

My saw is not as pretty, but same tank holder and air filter cover.

 

[Basher]

View attachment 330585 View attachment 330586 View attachment 330587 View attachment 330588

Very nice job, Gary.

 

[Gary Courtney]

Very nice job, Gary.

Thank you

 

[StihlMagnum440]

The X before the SN is just a mark the factory uses to indicate that the saw was tested. Later saws like the MS series will have an X at the end of the SN.


Serial #12938283 was the switch from 10-12 mm cranks

My 440 Magnum is a 165xxxx serial and the x is before the serial #. I never even noticed the x since buying it new in 1/6/2007. Interesting info. I got out of bed to go check my saw...geeez.

 

[StihlMagnum440]

View attachment 330585 View attachment 330586 View attachment 330587 View attachment 330588

Very nice. I have a 440 and a similar woodstove. The 440 has filled that stove non stop during heating seasons for years. Great combo especially with fuel cost now!
Got rid of glass on my stove door because found flames distracting...and I slammed the door once and a stick of wood came through the glass haha! Replaced glass with metal plate I cut with my torch and it looks factory.

 

[Gary Courtney]

Very nice. I have a 440 and a similar woodstove. The 440 has filled that stove non stop during heating seasons for years. Great combo especially with fuel cost now!
Got rid of glass on my stove door because found flames distracting...and I slammed the door once and a stick of wood came through the glass haha! Replaced glass with metal plate I cut with my torch and it looks factory.

We built this house in "83" and have never used the heating unit. That stove is the third stove and I heat 2400 sq. ft.