Jonsered 630 info

[redline4]

Just aquired a Jonsered 630 super along with a new loop of Oregon chain for $20.
Its my understanding it shares pieces/parts with some model Huskys. Which models? My interwebz searches have been vague and fuzzy in that aspect.
We dont have any dealer support here for J-reds, and the local Husky shop told me they never made a 268xp when I needed parts for mine...
It starts, races and dies. Kill switch is gone. Going to tear it down, replace lines, carb kit, etc. So any info as to what model husky it shares parts with would be great.
Also, whats the switch under where the kill switch is? Cant find any reference to it in user manual I found online.

 

[Johnmn]

630 is really it's own baby, yes it shared a lot of parts with the 61,266,268,272 huskys and 625,630,670 jonsereds but husky never made a closed port 60cc saw in that chassis. It's a strong 60cc saw for sure a little heavy but not bad.
You know what never mind, this saw sucks send it to me I'll give you $50 plus shipping!
Great saw, great price!

 

[redline4]

Thanks! That helps. First thing I noticed when I picked it up, it was pretty much like my 268xp.
I was wondering if I would get told it was a p.o.s. It's my first J-red, so I will probably keep it!
I think it will clean up pretty good too, it's not too beat up, just dirty.

 

[decableguy2000]

I'll triple your money on it? Good saws, parts are little more scarce for the Jonsered's than the Husqvarnas. It should perform close to your 268.

 

[p61 western]

Thanks! That helps. First thing I noticed when I picked it up, it was pretty much like my 268xp.
I was wondering if I would get told it was a p.o.s. It's my first J-red, so I will probably keep it!
I think it will clean up pretty good too, it's not too beat up, just dirty.

Keep the saw for sure, and @Stump Shot could probably tell you a little more about it.

 

[Stump Shot]

You have a 630 V , which is a heated handled saw.
What do you need in particular?
I'll quadruple your money. Lol
Yes Husqvarna parts will keep it going, I put a 266SE top end on this 630 V.

 

[redline4]

Thanks again!
I was thinking the switch was for a heated handle, but didn't tear into it yet.
As of now, the only broken part I found was the missing kill switch.
I will tear into it after I get done with a friend's 028.

I was going to press/vac test, and if that's good, stuff a carb kit, fuel line and filter, air filter, and the kill switch and run it a bit before doing anything else.
My biggest hurdle is Jonsered and Dolmar are unfamiliar to me, and local dealer support is zero on them, so getting info from you guys is the only way I can get it.

As of now, due to it being my first and only Red, my CAD is telling me to keep it and let it eat some wood!

 

[Onan18]

630 is really it's own baby, yes it shared a lot of parts with the 61,266,268,272 huskys and 625,630,670 jonsereds but husky never made a closed port 60cc saw in that chassis. It's a strong 60cc saw for sure a little heavy but not bad.
You know what never mind, this saw sucks send it to me I'll give you $50 plus shipping!
Great saw, great price!

Actually they did, it was the very first saw on the chassis, the 162 SE. The 162 and the 630 JRed share the same piston, cylinder, and intake block.

 

[Dub11]

Nice saw and you suck!

 

[Stump Shot]

Thanks again!
I was thinking the switch was for a heated handle, but didn't tear into it yet.
As of now, the only broken part I found was the missing kill switch.
I will tear into it after I get done with a friend's 028.

I was going to press/vac test, and if that's good, stuff a carb kit, fuel line and filter, air filter, and the kill switch and run it a bit before doing anything else.
My biggest hurdle is Jonsered and Dolmar are unfamiliar to me, and local dealer support is zero on them, so getting info from you guys is the only way I can get it.

As of now, due to it being my first and only Red, my CAD is telling me to keep it and let it eat some wood!

I have a used switch here if you need one, pm me your address.

 

[redline4]

According to the Acres site, they have max rpm listed as 8,700?
That cant be correct, can it?

 

[Johnmn]

Actually they did, it was the very first saw on the chassis, the 162 SE. The 162 and the 630 JRed share the same piston, cylinder, and intake block.

Learn something new everyday! Thanks

 

[decableguy2000]

12.5k per the 98 owners manual

 

[redline4]

12.5k per the 98 owners manual

Thanks. That's more gooderer! At 8700 rpm, I think my 12 year old daughter's mouth can run more rev's than that..Kid never quits talking!

 

[p61 western]

Thanks. That's more gooderer! At 8700 rpm, I think my 12 year old daughter's mouth can run more rev's than that..Kid never quits talking!

Lmao sounds like my 12 year old boy.

 

[Spike60]

As far as the RPM's go, 630's spin up to 13,000. (12,500 for the 625's and 13,500 for the 670's.)

V models in nice shape are pretty rare. You got yourself a nice project there.

 

[redline4]

As far as the RPM's go, 630's spin up to 13,000. (12,500 for the 625's and 13,500 for the 670's.)

V models in nice shape are pretty rare. You got yourself a nice project there.

I got lucky on this one. Other than dirt, grime and cobwebs, it's in real good condition.

 

[JMoney]

I'm loving the one @Johnmn sent me!

 

[Johnmn]

I'm loving the one @Johnmn sent me!

Good to know!

 

[Dub11]

Good to know!

Is that the one I had?