Search results

Hey Guys, I built an 034 for my buddy a few years ago and he just had his flywheel sheer off hit crankshaft. Looking for either a good bottom end to swap his top end over to, or a crank and I will do a full tear down on it. Thanks, Jordan

Pulled off a parts saw today. Grabbed a comp test before pulling it. It was mounted with no gasket. I have done no cleaning whatsoever to it, though I dont know it's prior life as I have never run it. Looking for $125 before shipping. Pics in following post.

Decided I may go the double ended bar route for milling, need another big saw if thats a case. Not in a rush to spend a bunch, but let me know what you have

Put this together when I had dreams of getting another 2100 going, have since realized that isn't likely. V-stack is poly and made by @srcarr52 Elbow is an aftermarket 288 elbow, which bolts on to 2100s. Will take a loss at $70 usd before shipping

Looking for a 50cc pro builder Ideally a 346 or carbed 261. May bo m-tronic, or with a 550xp autotune for the right price. Let me know what you have. Bonus points if you are in Canada

Thinking of downsizing further. In Hope's of getting a 3120 some day. This saw startsvand runs well. I have milled a few slabs with it. I did notice the pile is set up for a short bar though, so I havent milled with it as I havent had time to pull the oiler to switch it around. I installed...

Too busy with Reno's to finish this one. I have already replaced the crank seals with OEM seals as they were the problem with this saw. Cylinder has very light transfer. Have new meteor piston and an aftermarket muffler as it was missing when I picked up the saw Over 150 bucks in OEM parts...

Ended up not needing these. Missing the winter shutter on the top cover and the screen prefilter and adjustment grommet on the filter cover as seen in the pics. $15 plus shipping from L3V3S4 Canada

Have a velocity stack that came on a saw I got. I run 2 inch filters and this is 1-3/4" so it may aswell go. Looking for $40 plus shipping from L3V3S4 Canada

Was thinking of keeping this but I am going to test the waters. New OEM set of cases with badge from the donor 272 swapped over NOS non-decomp mahle top end, old box for proof Nice used fine thread crank and old style clutch New Oregon 7 pin rim sprocket and drum Nice tank with new OEM line and...

Have a fair collection after a few build. Will let the pictures do most of the talking. All prices are before shipping. Someone can take it all for $100 Fuel tank $15 2 piece coil crankcase pair $20 Good clutch cover SOLD 61 top cover (Missing 1 bolt) $5 Flywheel cover $3 Bad clutch cover -...

Looking for something ranging from an 026-261 to an 046-461 to fix up as my uncle is looking for a saw. I am in Canada which is limiting shipping wise but it is always worth the shot. Let me know what you've got. Thanks, Jordan

I have been sitting on a decent mine of 2-series parts including this 272. Bit of background on it. I bought if running for $80, took it home, looked down the muffler and saw a decent amount of transfer. I removed the transfer and put a hyway piston in it. Cut with it and it was throwing...

My Uncle liked my 046 Arctic too much. Looking for a builder to make him. Arctic would be a bonus. Let me know what you got

This is a nice clean 2165 I picked up recently. It got a new brake handle and a #4 nylon filter. Cleaned the carb with new gaskets and diaphragm. I cut a bush cord of firewood with it and it was a real solid saw. Revs up and idles down nicely Asking $400 pho or best offer. I haven't seen too...

Just picked up a decent start for a builder. Looking for the following Good piston and cylinder Brake handle Top handle Air filter cover Oil pump cover Felling dogs Brake band and spring Rear handle cover (the black part) Thanks in advance

Have a box of parts to build a 272, as well as a NOS top end. Has me thinking of making a nice saw. Bright plastics, decals, clutch cover may be nice. Just a looking to see whats out there, this thing doesn't HAVE to be pretty

Just discovered my dirt Bike cylinder is roasted so I need to free up some funds. This saw is in pretty good cosmetic shape. The cylinder seems to have been honed or some weird stuff at some point. I sanded it a bit and slapped it on with a base gasket delete and caber rings on it and put a...

Well, although it is referenced throughout the forum, I can't find a specific thread, figure this may help reduce multiple questions from guys like me. It isn't rocket appliances but I figured some pictures would help. 1: This is the little doohicky right here, slightly hiding behind the choke...

As the title states. Would prefer the new style like the 036 pro, but the saw has a 4mm case on it so the plastic 034 will do as well. Give me a price shipped to L0L1T0 Canada. Thanks all