DOLMAR/MAKITA The Official Sachs Dolmar Dolmar Makita Dolmar Chainsaws Thread

[ajschainsaws]

took the ole CT out again

 

[AlfA01]

All parts appear in stock in Germany.

I'd go new OEM on all except piston/P&C kit as they are pricey - I'd try sourcing an AM piston kit and salvage the cylinder.

AF cover - 024 118 112
Piston kit - 024 132 020
P&C kit - 024 130 300
Clutch cover , red - 024 213 290
Bearings, 6203 C3 - 960 102 171

Thanks. I've got a longer list now and a lot of questions before I order everything. I plan all OEM for sure.

Cylinder is in great condition, but gonna need piston and rings. Rod bearing was rusted, so it made it seem the piston was stuck in the cylinder.

 

[AlfA01]

Need some 9000/9010 help for some of you gurus. I don't have any tags or info on the saw to go off of.

Which saw had the green coil and Bing carb?

What were the differences in the flywheels and coils?

Which ones can/should I use when I rebuild this saw?

 

[Wilhelm]

Dolmar PS-9000/9010 IPL's

 

[mettee]

Now at The Home Depot . . . .

View attachment 143808
View attachment 143809


Philbert

Grab that thing, offer like 300, they take offers.

 

[AlfA01]

Dolmar PS-9000/9010 IPL's

So, I can't confirm my P/N's for the coil, but it appears this saw started life as a 9000....we're gonna have to see if we can change that.

@ajschainsaws how much do you get the 9000 to 9010 coil and flywheel conversion bits for?

EDIT: Thanks for the IPL's @Wilhelm I had some of those, but was missing the late 90's.

 

[Rob Stafari]

Just turned two of my dolkitas into dualkitas!

 

[mettee]

If I may ask, what set up is that? I want to eventually have one like that for milling my own stuff.

Grandburg?

 

[Philbert]

Just turned two of my dolkitas into dualkitas!

How do you coordinate RPMs?

Thanks.

Philbert

 

[Deets066]

How do you coordinate RPMs?

Thanks.

Philbert

Don’t matter, just pull the trigger In the wood

 

[Wilhelm]

Are any of those still available and any idea what the total cost would be shipping them this side of the pond? Oh yeah, how the heck do you figure those sizes out? Thanks.

None left, apparently I purchased the last one from the seller.
I was hoping to get another and one for You, but nope.

 

[ajschainsaws]

So, I can't confirm my P/N's for the coil, but it appears this saw started life as a 9000....we're gonna have to see if we can change that.

@ajschainsaws how much do you get the 9000 to 9010 coil and flywheel conversion bits for?

EDIT: Thanks for the IPL's @Wilhelm I had some of those, but was missing the late 90's.

I will check prices and get back too you

 

[Rob Stafari]

If I may ask, what set up is that? I want to eventually have one like that for milling my own stuff.

Grandburg?

Some bits are from a granberg MKIII that I found new in box covered in dust forgotten about in a barn. The rails are 8020 extruded aluminum tslot which I like better than the granberg style rails as they have a stronger profile. The round torsion bar is electric conduit. I could get all that stuff local so it was cheaper than granberg stuff.

 

[Rob Stafari]

How do you coordinate RPMs?

Thanks.

Philbert

Get them tuned the same with a tach and just go cut. The chain is only going to move at one speed regardless so they will synchronize.

 

[bigbadbob]

Dropped the 7900 off at the makita repair center for the chainbrake recall .
Will be interesting to see what the fix is.

 

[bigbadbob]

So got the saw.
They replaced the guts and one pin.
Had to remove muff to get at the pin.
He said the rivet heads on the guts face out now.
New brake flag to.

 

[Wilhelm]

So got the saw.
They replaced the guts and one pin.
Had to remove muff to get at the pin.
He said the rivet heads on the guts face out now.
New brake flag to.
View attachment 145220 View attachment 145221

Looks like there is added weight to the brake flag, to make it trigger easier/sooner?

 

[bigbadbob]

Looks like there is added weight to the brake flag, to make it trigger easier/sooner?

Looks plastic,, will check it out more now that you mentioned it.
May drill a small hole and see whats up.
I thought it was away to tell its been fixed.

 

[Philbert]

So got the saw.
They replaced the guts and one pin.
Had to remove muff to get at the pin.
He said the rivet heads on the guts face out now.
New brake flag to.

Thanks for sharing the details.

My brake flag is cracked (I have it spliced), so maybe they should recall the US ones too!

Philbert

 

[Simondo]

So got the saw.
They replaced the guts and one pin.
Had to remove muff to get at the pin.
He said the rivet heads on the guts face out now.
New brake flag to.
View attachment 145220 View attachment 145221

Bob. If you have the time , can you do a few more pics of that new brake flag from different angles?