Random pics (that you took) thread...

[Mkinslow]

Here's the river again this morning around 8:30am this morning

Sent from my SM-G892A using Tapatalk

 

[redline4]

Wont be getting out here today with the extra snow and wind.

 

[Bigmac]

Sunrise yesterday

 

[grizz55chev]

Sunrise yesterday
View attachment 167425

I know for a fact that pics don’t do justice to the real thing, I bet it was spectacular!

 

[grizz55chev]

Started to flood under the house, only 1-2" deep, but to save a mess from running in the garage I set this up with the trigger lock on

View attachment 167314

Video upon request, cuz it did happen

That’s some second level McGyver action right thar!

 

[Marshy]

Yup, frozen slider. Once pad was half used, other was slightly more than half.
Caliper seems fine. Might get a hardware kit.

 

[TreeLife]

My morning...

 

[chipper1]

View attachment 167441
My morning...

I think we have one of those on the Accord, need to check it out, but it's low for sure.

 

[grizz55chev]

Yup, frozen slider. Once pad was half used, other was slightly more than half.
Caliper seems fine. Might get a hardware kit. View attachment 167440

Ya only need 1 pad.

 

[grizz55chev]

View attachment 167441
My morning...

Don’t pull it!

 

[Marshy]

Passanger side is slightly better, at least not metal to metal. Still have uneven wear on the pads. Pisces me off. Not sure if the caliper is to blame or if that's the slide pins fault. The one pin on drivers was tough to move but freed up by hand. No rust, lube looked a little baked.

 

[Marshy]

Ya only need 1 pad.

Came with two, will stop with one or none (eventually).

 

[Only the Tony]

Three sets of splices in three feet of wire. Someone's fine work.

 

[redline4]

Drifts are about 6' behind my house now and the wind is still cranking.
Sun's out though.

 

[chipper1]

Here's the river again this morning around 8:30am this morning

Sent from my SM-G892A using Tapatalk

Looks pretty bad.
When we drove over the river this afternoon looking to the west you could see whitecaps about 2-3' high on the river, going upstream , I've never seen that before, the wind is cranking pretty good here.

 

[chipper1]

Meant to post this here, put it in the dirty work saw thread lol.
Couple pics from splitting a partial trailer load of elm yesterday. This is the one I dropped last Saturday iirc I posted pictures in here. There's still more of the tree left after the neighbors son took the stuff up to the main stem, I might grab that up if they don't finish it. They also asked me to drop a couple ash Ash and two 12-14 black locust, I'll be keeping the locust if I drop them, I like locust.

Between the trailer load(6.5'x20'x about a ft) and what I cleaned up off the ground to get the trailer jockeyed in there I added a good but over a cord, from the front of the pile it's hard to see I did anything lol.

 

[Steve]

Passanger side is slightly better, at least not metal to metal. Still have uneven wear on the pads. Pisces me off. Not sure if the caliper is to blame or if that's the slide pins fault. The one pin on drivers was tough to move but freed up by hand. No rust, lube looked a little baked.
View attachment 167446

Make sure your pads slide smooth in the bracket too. Those cars like to stick rear slides as you found and rust likes to build up under the stainless shims and lock the pads in the bracket.

 

[Mkinslow]

Looks pretty bad.
When we drove over the river this afternoon looking to the west you could see whitecaps about 2-3' high on the river, going upstream , I've never seen that before, the wind is cranking pretty good here.

It was pretty bad,but it dropped about 3 feet by this afternoon. Should be ok now.

Sent from my SM-G892A using Tapatalk

 

[Dub11]

View attachment 167441
My morning...

Could of been worse.

Like in the side wall

 

[Bigmac]

Went riding for a little bit today and had a decent rainbow