Not So Pro 3

[Lightning Performance]

@dall
Can you run the 024 or 024S jug on an 026 case with an extra base gasket installed?

 

[Hinerman]

That mfr would have been a rug.

You would have to be able to shoot it first........just sayin'

 

[Boomhower]

Unless you have a pile of these lil 026’s with no money in em its not worth it to rebuild em i think...

Theres a whole bunch of em in good shape in the classifieds around 250 range. Hell the 024’s @Mastermind sold a while back were mint and they were less than 300. An OEM topend is 186 on fleabay. Anyways thats my bitatch for the day...

 

[cuinrearview]

Unless you have a pile of these lil 026’s with no money in em its not worth it to rebuild em i think...

Theres a whole bunch of em in good shape in the classifieds around 250 range. Hell the 024’s @Mastermind sold a while back were mint and they were less than 300. An OEM topend is 186 on fleabay. Anyways thats my bitatch for the day...

Nobody wants them unless you have a door that won't stay open. Sorry to bear the bad news.

 

[Czed]

Well this is frustrating. The piston and cylinder I have will not work on this saw. The piston hits the cylinder on top of its stroke. Any ideas?

Grind the top of the piston off

 

[Boomhower]

Nobody wants them unless you have a door that won't stay open. Sorry to bear the bad news.

I like my 026’s. They fire right up and are light. I normally keep one in the ranger for trimming limbs on the trails. They just aint worth the cost of new parts to fix em.

 

[Boomhower]

Grind the top of the piston off

Possibly, hell i like Kennys idea but would need to be a spacer gasket i believe stacked would eventually blow out. Im just goin to see what the seller will do for me. Im moving on to next saw and put this one to the side.

 

[Czed]

I like my 026’s. They fire right up and are light. I normally keep one in the ranger for trimming limbs on the trails. They just aint worth the cost of new parts to fix em.

I rebuilt one for a guy meteor piston kit
With oem everything else except
No bearing change.
He was only pissed the 16" bar and chain cost like 85.00 he wanted
Everything else was 60 or so dollars.

 

[Lightning Performance]

I made some change buying them in piles to flip. Never had one 024 part but a jug and I still own it. Echo line and carb kits was about all they needed and seals or an oil pump replaced. Good little saws. Kept one like new a minty 260. Pawn shop find for 250

 

[cuinrearview]

Possibly, hell i like Kennys idea but would need to be a spacer gasket i believe stacked would eventually blow out. Im just goin to see what the seller will do for me. Im moving on to next saw and put this one to the side.

I kid. I like the slender chassis and the sound.

 

[Boomhower]

Posted up in the wanted section im sure someone will be along shortly. Shoot im on a roll now i made the small side crank seal puller might as well pull seals n replace the next one in line.

 

[Czed]

You would have to be able to shoot it first........just sayin'

I watched a 40+ season deer hunter
Rack all the shells out of winchester
30/30 convinced he'd shot and missed a 10 point buck
He hadn't fired a shot he had buck fever I guess.
I couldn't imagine what it'd be like to shoot at rampaging mountain lion
I guess I'd say *f-word you like that guy did.

 

[dall]

Did it burn in the fire?

yes

Same reason Mr Ray could have a full time job sending them to people.

Who’s that
And don’t feel bad I spent almost 100 bucks for a service manual for my tractor

@dall
Can you run the 024 or 024S jug on an 026 case with an extra base gasket installed?

Not sure

Unless you have a pile of these lil 026’s with no money in em its not worth it to rebuild em i think...

Theres a whole bunch of em in good shape in the classifieds around 250 range. Hell the 024’s @Mastermind sold a while back were mint and they were less than 300. An OEM topend is 186 on fleabay. Anyways thats my bitatch for the day...

Gotta get them cheap

Nobody wants them unless you have a door that won't stay open. Sorry to bear the bad news.

I have guys begging for a couple

Posted up in the wanted section im sure someone will be along shortly. Shoot im on a roll now i made the small side crank seal puller might as well pull seals n replace the next one in line.

what are you looking for?

 

[Egg Shooter]

Morning men. I think we had a visitor

View attachment 262678

House cat?

 

[huskihl]

House cat?

Lol must’ve been

 

[Stump Shot]

Got a load of chit firewood yesterday and parked it under the shed roof. Just going to take it out as needed. Good enough for burning now and will help make sure that there is enough for winter. Rained today and wood stayed nice and dry.

 

[leadfarmer]

You would have to be able to shoot it first........just sayin'

Have faith lill buddy....[emoji16]

 

[Egg Shooter]

Daughter took her oil-burning Equinox in to the dealer. 80k on the clock. They’re doing an oil analysis on it where she brings it in every 1000 miles for them to check consumption. Might have to check it more often as I don’t think she can go 1000 without adding to it. Apparently there’s a 100k transferable warranty on it

Damn near 2 stroke with that oil consumption.

 

[Egg Shooter]

Can't imagine what he is now.

How the hell did he follow a lawn boy mower around at that size.

 

[Boomhower]

yes

Who’s that
And don’t feel bad I spent almost 100 bucks for a service manual for my tractor


Not sure

Gotta get them cheap
I have guys begging for a couple

what are you looking for?

Lookin for an 026 topend as seller doesn’t have one


Sent from my iPhone using Tapatalk