JPX chain ?

[sawmikaze]

Nope. I'm talking old school made in Canuckistan real Windsor, not that ching chong shama lama ding dong sheeit from Blount(Brount) China.

No Bailey's? For why, dawg? The lack of ease ordering online when there site is consistently timing out, exorbitant shipping, near local pricing, or the chance of another security breach?

Oh and someone bought themselves a nice watch in texas with my credit card after baileys security breach..they can get fukked in my book.

 

[sawmikaze]

LCS had some 25" 3003 in GB Ti as a combo for really decent pricing. They may be 3/8 063, but they have 404 tips in stock.

I might try it

 

[junkman]

I dont run big saws often enough , i just had jay port a 660 for me that i have maybe 15 or so trees to use it on..after that it will get used once a month..maybe.

I might get a 404 set up on 25" with some full skip to noodle with though.

660's are to hebby for me ,i'm a sissy boy .

 

[radio]

I'm not sure what RMF is, but APX(APLX) is Windsor Full chisel, so it would make sense that it would dull faster in dirty conditions. I had a bunch of the Windsor, and in clean conditions it is pretty wicked.

That's odd for two different manufacturers to use the same nomenclature?

Are you sure it's Windsor APX and not Windsor 50APL?

 

[Jon1212]

Are you sure it's Windsor APX and not Windsor 50APL?

I'll see your "call" and raise.......

 

[radio]

I'll see your "call" and raise.......

There are some serious gaps in my chain knowledge

 

[Jon1212]

There are some serious gaps in my chain knowledge

Oh heck naw.....you're good.

 

[radio]

Oh heck naw.....you're good.

The only APX I knew was Oregon. I have a 25' reel of Oregon 72AP, the skip version of 72DP. They also have 72APX which is DPX skip.

 

[Jon1212]

The only APX I knew was Oregon. I have a 25' reel of Oregon 72AP, the skip version of 72DP. They also have 72APX which is DPX skip.

View attachment 25971

With two tie straps between cutters, is the AP semi chisel half skip?

 

[radio]

With two tie straps between cutters, is the AP semi chisel half skip?

It's semi-chisel full-skip. Semi-skip is a 3/2 sequence instead of a cutter every third link .

 

[Jon1212]

It's semi-chisel full-skip. Semi-skip is a 3/2 sequence instead of a cutter every third link .

See.......ya' learned me sumfin'

 

[radio]

Aw, I think you just did that to make me feel good, somehow I think you already knew about semi and full skip

 

[super3]

Off the roll/our of the box square is NOT near what square should be. I do not attempt to make race chains, work chains only and square is good stuff. I cut mainly hardwood and a lot of it is dirty, square doesn't rock as bad as round if filed proper. Just my $.02 from the south east.

^^^^ yep.

The working corner on sq holds up a LOT better than round chisel.

One file will last a long time for work chain and make a "great" raker file when the the edge finally gives up.

 

[Cracker Boy]

I agree junk man i run very similar i run rslh 3/8 on my ported 10 mm 044 hd2 filter and its bad ass my next loop will be rslf building a 12 mm 044 ported now with a 10 mm cylinder my fav saw hands down

 

[jake wells]

Oh and someone bought themselves a nice watch in texas with my credit card after baileys security breach..they can get fukked in my book.

http://www.loggerchain.com