Building the Solo 665 Hybrid!!!

[mdavlee]

But I'm scared.

I've thought about in the slower saw doing 96/126/and epoxy the intake back up to 79!

That sounds better to me.

 

[Miller Mod Saws]

The 81 intake saw I put a 2° angle on most of the squish band and opened it from .019 to .021" and took my comp from 230 to 210.

 

[mdavlee]

Don't need all that compression any way. I never tested Matts since my Shrader valves died in my tester. It was 165-170 before

 

[Miller Mod Saws]

I wanted less. Lol. As neither saw has had over 2 tanks threw it. So that said. My 210 will rise! Lol.

 

[Miller Mod Saws]

Harden baby harden!

 

[David Young]

But I'm scared.

I've thought about in the slower saw doing 96/126/and epoxy the intake back up to 79!

How about gasket stacking to move the durations for test.

 

[Miller Mod Saws]

How about gasket stacking to move the durations for test.

You could do that but you wouldn't get the true effect with the much larger squish. This saw is not lacking for torque at all so it will be ok.

Most I'll be out is a cylinder! The price of learning!

 

[Miller Mod Saws]

Ok boys lend me yours ears and I'll tell ya what I did. I'm very happy with both of these saws now!

Opinions and criticism welcome. Lol.

 

[Mastermind]

Less intake......and more exhaust.....

 

[Mastermind]

I like the second saw better.....

 

[exSW]

I like the second saw better.....

Me too. I would have liked to see you lean on that first one though.
I ain't even got my 2186/385 back from the little piggy and you guys got me thinking.

 

[jrsdws]

Second saw.....sounds like it's holding higher rpm but not giving up any torque.

 

[WKEND LUMBERJAK]

Ok boys lend me yours ears and I'll tell ya what I did. I'm very happy with both of these saws now!

Opinions and criticism welcome. Lol.

It's not mine. . LOL

 

[Miller Mod Saws]

Randy you nailed it. This is the saw I dropped the comp on by angling the squish 2°. I epoxied the intake back up to 79°. And before I had the main trans pretty flat and the secondaries pretty steep. I flattened the secondaries so them and the mains are angled up just a little and it's sitting at 96/125/79. now that said that's with pushing a ring up in to get my heights. If you flashlight it the exhaust looks to be at 94. It's still not lacking for torque with a 28" bar and is singing a nice little tune. The 98 saw is a tad torqueier and I think it may show when I strap a bigger bar on but I'm happy with both of these saws right now.

 

[Miller Mod Saws]

It's not mine. . LOL

I can fix that.

 

[Mastermind]

It's damn sure sounding good.

I've still got a couple of Paul's saws yet to finish......but I'm excited to start on the Solos again.

 

[Miller Mod Saws]

It's damn sure sounding good.

I've still got a couple of Paul's saws yet to finish......but I'm excited to start on the Solos again.

I'm excited for you to start again as well. Hopefully we can figure this baby out together.

 

[Miller Mod Saws]

At this point I'm in debate whether to tear the slower saw back down. Lol. I did spend several hours today trying to mock up the rwj4 carb on it. Just couldn't find a combo I liked without doing some hacking. And I'm not hacking these saws. I want them to be solid work saws when I'm done!

 

[mdavlee]

Is it that much different than the dolmar for fitting it?

 

[Miller Mod Saws]

Is it that much different than the dolmar for fitting it?

Well idk I havnt did the dolmar either.