WANTED 242/254/262 XPG Generator

[Derf]

Looking for a stator/generator that goes behind the flywheel in good condition.

Also looking for a heated handle switch.

 

[dustinwilt68]

https://www.ebay.com/itm/OEM-Husqva...984529?hash=item1ec0949f91:g:FAsAAOSwUKxYjqFO

It's the same generator you need

 

[Derf]

That wasn't what I needed, it's the wrong size and bolt pattern.
Bump

 

[Glock37]

On 242 make sure get sleeve and seal needs to be set deeper


Sent from my iPhone using Tapatalk

 

[Glock37]

Looking for a stator/generator that goes behind the flywheel in good condition.

Also looking for a heated handle switch.

Switch same as 395

Generator same as 395




Sent from my iPhone using Tapatalk

 

[Derf]

Thanks for the suggestion, but apparently that one didn't fit either. Should have known, the 394/395 generator has a different part number than the 254/262 part number.

For anyone curious, this is what a 242/254/262 generator looks like.




This is what a 395 generator looks like.


Notice that there needs to be 3 mounting screw holes that line up, AND, the center hole is just barely bigger than the shaft diameter. For anyone coming down this road in the future, don't waste your money buying the wrong part - they don't cross over.

 

[Glock37]

Ask @Spike60 hes close to u and will know


Sent from my iPhone using Tapatalk

 

[Spike60]

Fred is correct that the 395 item isn't going to fit. I don't have anything laying around myself. Experimentation with 346/357 or 550 generators might yield some results, but they'd be pretty expensive experiments unless you already had them laying around.

 

[jockeydeuce]

If I was a betting man, I'd say that's the same stator as an 028 etc. Stihl....

I've got a new one

 

[TUBBER 340]

Looking for a stator/generator that goes behind the flywheel in good condition.

Also looking for a heated handle switch.

I’ll look in hr and let you know


Sent from my iPhone using Tapatalk

 

[Derf]

If I was a betting man, I'd say that's the same stator as an 028 etc. Stihl....

I've got a new one

View attachment 179121

They do look Very similar. Can you take a pic of it from above next to a ruler and PM me the pic. I’ll scale it to size and print it, cut it out and lay it on the case to see if it would fit.

 

[Quzick]

i might have one generator. ill try to make a picture after work!

 

[jockeydeuce]

Don't know if this helps enough....outside is roughly 2 1/8"

 

[Quzick]

Here is mine...

 

[Derf]

Don't know if this helps enough....outside is roughly 2 1/8"

View attachment 180514

That’s perfect, but it says SEM Sweden on it... is this a Husqvarna part, or a Stihl part? I was curious if the Stihl part is easier to source if it will swap over.

 

[Derf]

Here is mine...

For sale?

 

[jockeydeuce]

That’s perfect, but it says SEM Sweden on it... is this a Husqvarna part, or a Stihl part? I was curious if the Stihl part is easier to source if it will swap over.

Mine is a Stihl part....# 1118 400 4000

Mine's for sale if it will work for you

 

[Quzick]

For sale?

yep for sale!

 

[Derf]

Mine is a Stihl part....# 1118 400 4000

Mine's for sale if it will work for you

PM Sent