High Quality Chainsaw Bars Husqvarna Toys Hockfire Saws

SELLING 066/056 Mag II hybrid diy kit

Trader history (4)

Woodslasher

Teh debil
Local time
3:13 PM
User ID
15993
Joined
Mar 18, 2021
Messages
3,572
Reaction score
14,582
Location
Commiefornia
Country flag
Awhile back I decided I was gonna build an 066/056 Mag II hybrid so I assembled all the parts, got the cylinder to bolt down, and that was as far as I got. I know that either the band needs to be cut or a spacer fabbed up, I just no longer have the time or motivation. Or, sell the 056 top end and bolt on an 066 cylinder and just run that. In any case, I'm selling the whole parts lot as a unit.

Here's a fairly comprehensive list of what's included:

OEM parts:

Top cover
2 carb boxes and a filter base
Loaded crankcase
056 cylinder
Carb
Coil
Misc smalls are all oem as I recall

A/M parts:

Unknown recoil and fuel tank
Madsens 3/4 wrap, I think it's a bit tweaked but fixable
Hyway wide clutch cover
Hyway DP muffler with the outlets opened up a bit
2 Hyway big bore pistons

IMG_9181.jpegIMG_9182.jpegIMG_9183.jpegIMG_9184.jpegIMG_9185.jpeg
 

timg

Supporter of Cat Eating Komatsu Machinery
GoldMember
Local time
6:13 PM
User ID
8928
Joined
Mar 7, 2019
Messages
4,420
Reaction score
24,184
Location
Keystone State West
Country flag
Looks like a good challenge for your machining capabilities Greg. I think you may need to devise a decomp port somehow too. Daniel, No embedding of material on that cylinder wall? Maybe just the pic but it looks a little rough.
 

farminkarman

I like the red & black ones
Local time
5:13 PM
User ID
13535
Joined
Aug 17, 2020
Messages
4,625
Reaction score
26,899
Location
Neenah Wisconsin
Country flag
Looks like a good challenge for your machining capabilities Greg. I think you may need to devise a decomp port somehow too. Daniel, No embedding of material on that cylinder wall? Maybe just the pic but it looks a little rough.
It is intriguing to be honest
 

ManiacalMark

Pinnacle OPE Member
GoldMember
Local time
6:13 PM
User ID
8282
Joined
Jan 2, 2019
Messages
1,068
Reaction score
2,463
Location
PA
Country flag
Looks like a good challenge for your machining capabilities Greg. I think you may need to devise a decomp port somehow too. Daniel, No embedding of material on that cylinder wall? Maybe just the pic but it looks a little rough.

You really just change the angle of the exhaust port and it works, but then the cylinder is only good for a 64/66.
 

Woodslasher

Teh debil
Local time
3:13 PM
User ID
15993
Joined
Mar 18, 2021
Messages
3,572
Reaction score
14,582
Location
Commiefornia
Country flag
Looks like a good challenge for your machining capabilities Greg. I think you may need to devise a decomp port somehow too. Daniel, No embedding of material on that cylinder wall? Maybe just the pic but it looks a little rough.
Doesn't seem to be anything embedded, just marks.
 

Bill G

Here For The Long Haul!
Yearly GoldMember
Local time
5:13 PM
User ID
2807
Joined
Mar 14, 2017
Messages
5,095
Reaction score
13,310
Location
Illinois
Country flag
When someone buys this I might have a few parts here to help them along........no good ignitions though
 
Last edited:
Top