JonCutter thread...

[Spike60]

How are those 62cc X-Bull's?

I just CAN'T get an orange Joncutter. I've got a 100 orange saws as it is.

 

[Leafy]

I bought a 62cc x-bull and I measured it when it arrived and it was a 52cc and they refunded me.

 

[Simondo]

If, the Joncutter saws have there roots in the Zenoah brand then this may be of interest.
There are 2 saws that the Joncutter G4500 " May" be based on ....
One has more power than the other in stock form.

 

[Leafy]

They're pre-strato. They exist as such good copies because zenoah licensed the construction of the whole saw into China just before the switch to strato for the American market.

 

[NSEric]

I think this one is actually 62cc. It also has the clip on style top cover so you can add the better filter without buying a top cover too.
https://www.ebay.ca/itm/Gas-Chainsa...382958?hash=item3b209f536e:g:MdIAAOSw6U5bqwot
DIY with uncle cy has a review of it on youtube, it cuts pretty good which is why I think its a 62. The bar/chain it comes with is junk tho.

 

[CR888]

I bought a 62cc x-bull and I measured it when it arrived and it was a 52cc and they refunded me.

I here quite a few China saws are like that, they often lie about the real displacement. Honesty, ethics & moral fibre are tossed far when it comes to putting cheap China product in the hands of consumer. I dare say 90%+ would never know their saw was 10cc less than it should be. The typical Jon cutter cutty-cutty fast saw purchaser would struggle to remove the air shroud.

 

[kgj1119]

I’m thinking about getting the 5800. What bar and chain fit these


Sent from my iPhone using Tapatalk

 

[Czed]

I’m thinking about getting the 5800. What bar and chain fit these


Sent from my iPhone using Tapatalk

ko95

 

[Leafy]

K095 mount. But the factory.325 20" bar is more like 19" so it uses a weird dl count chain, there's a guy on ebay that seems to be making lgx chain off a roll if you search by the drive link count. But if you put a normal length bar on it it'll use a normal dl count. You're probably getting a spur clutch on it so if you want to switch to 3/8 you'll need a new clutch.

 

[kgj1119]

K095 mount. But the factory.325 20" bar is more like 19" so it uses a weird dl count chain, there's a guy on ebay that seems to be making lgx chain off a roll if you search by the drive link count. But if you put a normal length bar on it it'll use a normal dl count. You're probably getting a spur clutch on it so if you want to switch to 3/8 you'll need a new clutch.

I thought the 5800 came with a 3/8 not .325?? I may be wrong though


Sent from my iPhone using Tapatalk

 

[NSEric]

I thought the 5800 came with a 3/8 not .325?? I may be wrong though


Sent from my iPhone using Tapatalk

It does.
It also has a rim sprocket so you can switch easily.
Huztl specs a 20 inch 3/8 bar and chain for the 5800. I think its much better with a 16 inch .325 like most 50cc saws are.
I put a stihl ms250 3/8lp bar on mine with the stock 3/8 rim sprocket for a bit. This set up is probley the fastest but I like .325 better so I switched to that.
You could buy the bar/chain for the joncutter 3800 from huztl and put it on the 5800 if you want 3/8lp or the bar/chain/rim sprocket for the 4500 if you want .325.
They're all K095 or small husky mount like a 450, 51, 350, etc.