Search results

Hey guys, I was asked to do a Muffler mod on a newer MS391. I've done plenty with older ones, the only question I have is about the carb. Are there adjustment stoppers in the carb, if so is there enough room to accommodate the mod or do they have to be removed.

Hey everyone, in mid May I will be going to Tennessee for a family vacation. We will be staying near Gatlinburg. I have not looked too far into this as a possibility but I am interested in hunting hogs. I figured there may be some trusty folks in here that could help. I did a quick search and it...

I know theres a few discussions on battery saws, good info, just not what I'm looking for. My grandfather will be retiring his 021 soon, he doesnt use it much at all and it's more of a hassle for him than anything. I'm thinking of getting him a battery powered saw. He really only trims...

Looking for a stihl 021-025, or a comparable size quality make. It will be my father in laws for small needs around the house so I'm looking for stock and oem. Does not need to be running. I wouldn't mind putting some work into it for the right price. Let me know if you guys have anything...

My father owned this 3 wheeler since new I think, it's been sitting with no fuel for 12-15 years. I've been wanting to get it running for several years, well I recently moved out and i just acquired said 3 wheeler :aaaaa: Threw a little gas in it and it fired and ran well on the third pull, but...

Hey yall, I've been looking for a tractor to have at my house for a while now. Ideally I would buy a 30hp ford with 4wd, a loader and plow. That set up, and pretty much any 4wd with a loader is pretty pricey and rare where I'm at, I don't really have 10k to spend on a tractor at the moment. I...

Hey y'all, I have a farmertec 440bb that I'm going to build, before I got into that I wanted to practice on this standard bore, I ran this at Randys' this past October in class 2. Since Randys' I moved the lowers over and filled them quite a bit with jb weld, i also cut the finger ports, to open...

Hey guys, I have a toro 826 with a Briggs. When it gets hot it lopes real hard unless I engage the choke. As it gets hotter I have to give more choke, until it doesn't well at all. When it does get hot it back fires and shoots flames out the exhaust. I'm going to order a carb or a carb kit...

So I read the three threads on porting saws, so clearly I now know everything there is to know:jaja-no:. Question is, if I were to use a material to fill transfers or a crank case, what would you guys use?

I'm working on an MS 270 my uncle sent to a shop recently where they replaced the coil. He said its not running right, warms up and dies. I took it, it starts idles poorly. Checked inside carb, air filter, tank breather, changed fuel, reset carb to factory, and it likes to flood. Checked spark...

Looking for a builder saw, open to any color or condition, but a whole saw would be better, I have 0 dolmar anything. thanks in advance

Hey guys, I'm looking at a stihl 075av. The guy wants 300 for the saw a 36" and 48" bar. Just wondering if anyone knew the going rate for this saw used, running, with life left. I don't know much more about it. I've seen them going for around 300 up to 1300. I feel like the high end is a bit...

So some things happened while doing some cuts to tune. Found a clutch spring broke a loop off and a retainer broke on one of the clutch pads. Half of the retainer is still there and stays on until you really try to get it off. Would anyone attempt to run it that way. I replaced all 3 springs...

Hey everyone, I have a rider with a 24HP Briggs model 445677/0413/e1. I just replaced the cylinder head and set my valve lash to .005. Is that enough/too much lash? Thanks, Jake