Search results

562xp - 2016. Complete and will start but will NOT idle. Saw is slow to come back to idle too. Had plans of finding the air leak? or finding the issue. It's been sitting here for over a year so it needs to go. When I got the saw it was lightly scored and wearing a 12mm Stihl bar. Plan was...

MS362 came in that had lost the choke rod connecting the thumb lever to the choke shaft. No problem ... even found one in stock local. Put it on and it did not fit great but it functioned and away it went. Well I get a call right back from the customer that it worked for a day and then it...

SOLD SOLD SOLD Stihl 020T which is just an MS200T with screw in caps. New 14" bar and chain. Cranks well, oils, idles, etc. Clean saw in better shape than most. Ready to go in a tree. Listed locally for $575. I'll do better on here plus the ride. Paypal preferred.

Tillitson HT-12E. This carb has minimal use on it. Long story but I put it on an 880. Customer was not happy and to keep face I sent a new OEM carb with the saw to be ported. I was playing with the jetting a bit but could never make the customer happy. IF you have never been around an 880...

SOLD-SOLD-SOLD New Shindaiwa 600sx that has never seen wood. Has manual & tool kit but no original box. I got this in a trade from Joe @Red97 . He has run this saw for a few minutes on his dyno but it has never seen wood. Its a beautiful saw but I honestly have no need for it. As seen in...

Husky 357xp / 359 full wrap kit. Bought for a saw that I never really used. Ended up getting rid of all of my 357/9 saws and this is left.. never had a chain pitched or anything. One small mark on the clutch side bottom of wrap as pictured. I think I ran this saw for one tank. Looking...

Looking for a Husky 340/345/350 crankcase that takes the primer bulb (extra molding by carb floor if I am not mistaken). Have swapping stuff but probably just send money. Will take a whole primer saw if needed. This is for my dad or I would never mess with it. The primer makes his life much...

My books do not go beyond the BR600. Can anyone confirm the carburetor setting procedure is the same to the BR600? Idle speed at 3000 then richen the low to bring it to 2500 rpm. Then high at Max rpm -100 rpm rich; then lean out 1 turn? Sent from my SM-G970U using Tapatalk

Stihl MS440. All OEM except the orange plastics. OEM plastics are here and can go with it if you want them. Cranks, runs, oils as it should. 20" bar and new chain included. I can get a piston pic if you really need one and I can get a compression reading too. Its stock including the carb...

I have a 200T in for a rebuild. It has had very poor maintenance from a dealer for some time. It is missing the dowel pins (hollow rivets is what they are listed as) that line the cases up. I have ordered new from my dealer but they are on back order. I can either send brand new pins on...

Looking for a tank for a buddy. Anyone have one laying around?

So back in 2013 I built my first 372. Immediately my dad wanted one too (all he had ever had was a 750EVL) and I won a Big Bore top emd at the Central VA GTG. Moobs standing there said "those make good runners" [cannot remember white or brown box]. He took it with him and a few weeks later I...

So I just put a top end on a MS362c. Standard procedure I would think would be reset the electronics after the replacement and a few heat cycles. The procedure for this flavor M-tronic I believe is 90 seconds of Choke/Start position and then shut the saw down with out touching the throttle...

So I recently picked up a CS 4400 from a member here. Great condition under the mung... only real mark is a chunk knocked out of the rear handle in shipping. Looking it over I thought it had very low hours..but the clutch spur drum is worn totally out. OK....looking for one and I see Echo...

Looking for a used MS360 fuel tank. Have used two AM tanks and this used keeps breaking them. They are fine when they leave and then a few months later the seam comes apart. I am going to try to plastic weld and epoxy this one but I know that an OEM is the only real long term solution.

MS201TC showed up today. Tree service saw purchased March of 2017. He generally does not like the saw. Last few months and it has been to two or three other Stihl shops. Everytime it comes back worse than when dropped off. Fast forward to today...saw is to a 'No Start' condition. Quick...

Recently picked up a running Echo twin. The sad is it is pretty beat. Looking for a non running twin that needs ignition. I need a bunch of small items so it's probably best to start with a non runner collecting parts. I guess the flip side is if someone is looking for ignition components...

Anyone else have issues with Tsumara bars need one less DL then they claim? Local tree service was looking for a new 32"/105DL bar for a kit 066 I built them. I suggested a Tsumara and ordered one. Immediately noticing that the chains are one DL too long OR they will never be able to run...

SOLD! Okay... the next box out of my stash....044/046/440/460. OEM MS440 Jug... crank exploded and this one may make a race jug. OEM 046 Mahle D jug. Light score..this one actually came in running. OEM MS440 plastics. Complete set with brass grommets. Extra AM top cover with OEM badge...

Jonsered branded 18" K095 mount (small Husky / 8.2mm) new in package bar with 5 new semi chisel chains. Chains are no name chains but I think most have seen any chain will cut, may just not last as long as big brand. I was told the crew at Left Coast had good luck with this chain. I bought...