What's on your bench?

[tickbitintn]

On to the other bench and turdy thou is gone.

Sent from my XT1635-01 using Tapatalk

 

[MustangMike]

Someone familiar with this model pipe up, should he raise that exhaust a bit?

 

[JohnnyBlade]

Got me a hillbilly set up! Didnt get a bolt but i found something to fit! FLMAO!!! Let me know what u think of these #'s. These r stock with BGD. 2159 Jonsered.
I- 80
T- 127
E- 103
I think i did it right.
When intake closes take number
When transfers open take number
When exhaust opens take number
Trans minus exhaust = blow down??????
Edit. Squish is at .022

 

[Frank bierce]

Bottom end of a pro Mac 700. Lol. Surprisingly, piston and cylinder look great!

 

[Dub11]

Got me a hillbilly set up! Didnt get a bolt but i found something to fit! FLMAO!!! Let me know what u think of these #'s. These r stock with BGD. 2159 Jonsered.
I- 80
T- 127
E- 103
I think i did it right.
When intake closes take number
When transfers open take number
When exhaust opens take number
Trans minus exhaust = blow down??????
Edit. Squish is at .022
View attachment 157986

You ain't got no hills around there......

 

[JohnnyBlade]

You ain't got no hills around there......

Lol! River rat set up then

 

[Wilhelm]

View attachment 157799Water in gas

Did You get drunk new Year and pi$$ in Your own tank?

 

[big t double]

View attachment 157846
Anyone want a roll bar?

View attachment 157882

View attachment 157883

View attachment 157884

View attachment 157885

Done, looks $1,000.00 better.

You get to bill that labor? I woulda got 1.5 minimum. Just sayin.

 

[MustangMike]

I- 80
T- 127
E- 103

I'm not familiar with this model, but seems like good #s to me. Perhaps raise the transfers a bit, but let someone with more experience with this model comment on that.

 

[redlight066]

Here's Hans. He's put about 40 lbs on since February. Still prolly another 50 short of where he was before the battle with cancer. He's supposed to get checked every 3 months for reoccurrence. Told me he found a small lump on his neck again before Christmas. Damn......

Regardless he was floored that I got his saw back to him in a day. Luckily between the two of us there was enough new and good used parts to make it work. Just to see him smile was enough.
here's a pic of his old crankcase

 

[redlight066]

Time to get back to work......

 

[Onan18]

You get to bill that labor? I woulda got 1.5 minimum. Just sayin.

Yes sir, upgrade on an older unit (this one was a 2001) got 2.0 hours out of it.

 

[Cut4fun]

#3 445 build 70.7cc for my wants again.

I had posted this in the chainsaw repair group after pulling nos and used parts for guys.

Just for this series of saws. Not even counting the shelf full of parts saws still.

After searching for parts for the air injection and muffler gasket for a member here and building 445 #2.
I realized my 8-9 bins full of parts was all disorganized.
Last night I set everything out on floor and put the parts in bins as parts groups.
I also noticed I was getting low on some parts after I been selling alot off for folks to get their saws going again. So slowing down on what I will sell in this series. Still plenty of parts just some stuff I wont sell till I quit running this series. With that said parts pulled to make #3 PP445 in all yellow were pulled out. Yellow updated tank with updated air filter set up and yellow cassette for chain brake.

 

[Wolverine]

View attachment 158018 Here's Hans. Just to see him smile was enough.

Good on ya sir!

 

[huskyboy]

Bunch o chit to build a 350.

 

[huskyboy]

Went into the 7900 the other day I built up a while back to check it out because I was bored. No harm in doing a few changes . So easy to work on this saw.

 

[MustangMike]

Are you adding more bananas???

 

[NeSurcaster]

first try with posting pictures so here goes.
Here she is

 

[JohnnyBlade]

I'm not familiar with this model, but seems like good #s to me. Perhaps raise the transfers a bit, but let someone with more experience with this model comment on that.

Thanks Mike. Ill let it stew a lil longer.

 

[NeSurcaster]

first try with posting pictures so here goes.
Here she isView attachment 158080 View attachment 158082 View attachment 158080 View attachment 158082

Almost did it right, also tried to reply or qoute my first post where talked about putting the new grips on the handlebar