The Freedom Saw

[Dub11]

My Dad did not say much about the war, but I think the most memorable line he stated was this:

He was a radio operator in the Tank Destroyers, operating in the wide open farm fields in Germany. But as a radio operator, they issued him a 30 cal carbine. I asked him what he did with that, and he replied "The first thing you did was trade the carbine for an M-1, with someone who did not need his any more".

My Grandpa said the same thing plus get the *f-word away from the machine gunners

 

[Redbull661]

Redbull is now offering free port jobs!

btw that poosie bullit is a 9mm

 

[T.Roller]

Redbull is now offering free port jobs!

btw that poosie bullit is a 9mm

Nice so are you over your little tantrum

 

[T.Roller]

Well boys we are gonna try this one more time and see what happens. Here's what I got this time

 

[T.Roller]

 

[Redbull661]

Nice so are you over your little tantrum

not yet. I haven't got to port no jugs yet! and I gots mah panties in a bunch and that *f-worder Ted done drank all mah beer!

might try dis here pill

 

[T.Roller]

not yet. I haven't got to port no jugs yet! and I gots mah panties in a bunch

might try dis here pill while me waits!

I'll take 3

 

[T.Roller]

The numbers on the cross jug are almost too good to fool with
Ext. 101
Int. 82
Trans. 118
Squish .018

 

[p61 western]

Is the weather good enough to blast that last jug?

 

[T.Roller]

Is the weather good enough to blast that last jug?

It sure is. Give me a bit

 

[p61 western]

It sure is. Give me a bit

Right on thank for some entertainment Dave.

 

[astnmacgto]

Right on thank for some entertainment Dave.

Ask and ye shall receive

 

[MustangMike]

Those look like real nice #s!!! I would just double check all the bevels. Some of mine did not feel right even if they looked OK. I went over all of them with 220 grit, and used the paint stirrer with a 45 degree cut to help me reach the tops of the intake, transfers, and exhaust (makes it a lot easier on your fingers).

 

[T.Roller]

Right on thank for some entertainment Dave.

I hate to bum you out but I got caught up tinkering with the saw. Before I knew it I was fueling it up and starting it! I promise tomorrow for sure brother

 

[T.Roller]

Those look like real nice #s!!! I would just double check all the bevels. Some of mine did not feel right even if they looked OK. I went over all of them with 220 grit, and used the paint stirrer with a 45 degree cut to help me reach the tops of the intake, transfers, and exhaust (makes it a lot easier on your fingers).

I triple checked this one Mike lol I cleaned up a few areas and beveled a few more with my fordom.

 

[p61 western]

I hate to bum you out but I got caught up tinkering with the saw. Before I knew it I was fueling it up and starting it! I promise tomorrow for sure brother

No worries, that is better yet that you got the saw running again. How does it run Dave?

 

[T.Roller]

Here she is. Swapped out my plastics so I could send the others for air brushing. Big big big thank you to @dall for everything. It wouldn't be possible without your help brother.

 

[T.Roller]

No worries, that is better yet that you got the saw running again. How does it run Dave?

Hadnt put a bar on it but ran it thru a heat cycle. Seems great.

 

[T.Roller]

 

[p61 western]

Sounds good and seems to idle ok.