not so pros

[beaglebriar]

Not much did some yard work and cleaned up a couple saws. How about you anything cool going on?

Stuck a couple Benjamin's in my pocket and got the 5105 put back together. Thats a nice running little saw.

 

[Stump Shot]

Yeah, I know all about the hearing thing, in the early days I ran the those old Macs with no hearing protection and now I pay for it.
Remember what I said about 45 degreeing the corner of the popup, I didn't get as much comp as I should have and I think that is why, the next one I do I will just round the corner a bit & try that.

Good point. @Czed Dave, would you like the edge of the pop up angled, square or the just the very outside corner knocked off?

 

[Time's Standing Stihl]

Hi there gazer... how's work?

About to call it quits for a couple days!

 

[p61 western]

Hi Dj

Good evening Bish, how are you doing?

 

[p61 western]

Good point. @Czed Dave, would you like the edge of the pop up angled, square or the just the very outside corner knocked off?

Good evening Steve, how are you doing tonight?

 

[beaglebriar]

About to call it quits for a couple days!

You suck... I go back tomorrow.

 

[Stump Shot]

Good evening Steve, how are you doing tonight?

Pretty good Mike, relaxing having a cup of coffee. How's things in Cali-del Norte?

 

[Time's Standing Stihl]

Good evening Bish, how are you doing?

Ready to go home and eat supper!

Do anything productive today?

 

[p61 western]

Pretty good Mike, relaxing having a cup of coffee. How's things in Cali-del Norte?

Everything is good out here, a little warm still but not bad.

 

[p61 western]

Ready to go home and eat supper!

Do anything productive today?

Yep got the yard work done and a couple saws cleaned up. Also touched up a square chain, so the saws are ready to go as well as the chains.

 

[Jon1212]

The ol' pooch screwing trick...

The kid working that day was having trouble with the address.

 

[old guy]

I've been wanting to try the 268 piston. What diameter do you turn the pop up?

Basicly went in 10 m/m with the cut leaving a 30 m/m diam. popup on a 50 m/m piston, the new piston was .060 taller than the stock one, now add in the .020 base gasket and took the cut .040 deep for 10 m/m, this gave me .023 squish.
This worked on MY SAW, do your own measure.

 

[Czed]

Good point. @Czed Dave, would you like the edge of the pop up angled, square or the just the very outside corner knocked off?

Outside edge knocked off i will try to measure tommorow.
Not running a base gasket on mine.

 

[czar800]

Hi guys my first post on not so pros.

Welcome to the madness,

 

[czar800]

Good evening everyone. Hopefully everyone is staying safe out there.

 

[ramrat]

How's it goingLee, tripback go well for you?

Good Steve. I should have left earlier was a short night. But was well worth it.

 

[beaglebriar]

Basicly went in 10 m/m with the cut leaving a 30 m/m diam. popup on a 50 m/m piston, the new piston was .060 taller than the stock one, now add in the .020 base gasket and took the cut .040 deep for 10 m/m, this gave me .023 squish.
This worked on MY SAW, do your own measure.

Basicly went in 10 m/m with the cut leaving a 30 m/m diam. popup on a 50 m/m piston, the new piston was .060 taller than the stock one, now add in the .020 base gasket and took the cut .040 deep for 10 m/m, this gave me .023 squish.
This worked on MY SAW, do your own measure.

I'm sure the squish would have to be adjusted slightly but the diameter should be close enough. I'll do some measuring for sure. Thanks

 

[leadfarmer]

I've seen you "workn"

That will be enough of that nonsense, I had sweat runnin down my brow mister [emoji38]

Sent from my SM-G900V using Tapatalk

 

[beaglebriar]

Outside edge knocked off i will try to measure tommorow.
Not running a base gasket on mine.

Could end up being a sparkplug knocker without a gasket. The pop up might need to be trimmed a whisker.

 

[beaglebriar]

Good evening everyone. Hopefully everyone is staying safe out there.

Evening Mike.