High Quality Chainsaw Bars Husqvarna Toys Hockfire Saws

Not So Pro 3

Kiwioilboiler

346 Pic Examiner
Local time
3:37 AM
User ID
12322
Joined
Apr 20, 2020
Messages
9,785
Reaction score
64,596
Location
Marsden Pt, NZ
Country flag
i had a pagero, Japanese grey import. I had it about 10yrs, the insurance was high cos of the grey import. And it drunk fuel 20\25 mpg.
Also had a very rusty chassis at the rear wheels,
And the manual gearbox went on me, the lay shaft was rattling for a long time, I put a 2nd hand one in, that was fun “not”

but I did enjoy having it ,,,
Pre 99 models certainly not as well regarded here as from 99 on Sean.

It sounds like you got a right 'Pajero' in Spanish huh.
 

Dub11

Saw R skeery
GoldMember
Local time
10:37 AM
User ID
2014
Joined
Oct 21, 2016
Messages
34,583
Reaction score
147,065
Location
Kansas
Country flag

Mastermind

Chief Cat Herder
Staff member
Yearly GoldMember
Local time
10:37 AM
User ID
4
Joined
Dec 3, 2015
Messages
52,571
Reaction score
350,222
Location
Banner Springs Tennessee
Country flag

GCJenks204

"Special Buns"
Local time
10:37 AM
User ID
367
Joined
Dec 31, 2015
Messages
15,510
Reaction score
98,634
Location
Winnipeg, MB
Country flag

redline4

I'm huge in Japan
Local time
10:37 AM
User ID
5593
Joined
Mar 12, 2018
Messages
13,277
Reaction score
112,345
Location
Rosholt Wisconsin
Country flag
Morning guys.


The single acting cylinder on my alignment hoist began to leak fluid out the cylinder vent about a week ago. It's of course been getting worse.
Yesterday my manager "fixed" it...

20211208_163543.jpg 20211208_163538.jpg 20211208_163545.jpg

I'm hoping when the piston seals completely give up and it won't work at all a car is stuck on it with the ramps sitting on the locks just out of spite. Hopefully it's a used car. I actually would feel really bad if a customer had to go without because of this chit..
 

USMC615

Fapper Fi
GoldMember
Local time
11:37 AM
User ID
976
Joined
Mar 1, 2016
Messages
21,197
Reaction score
114,018
Location
Mid-Georgia
Country flag

cuinrearview

Handy dood
Local time
11:37 AM
User ID
9248
Joined
Apr 16, 2019
Messages
11,189
Reaction score
77,776
Location
Dowling, MI
Country flag
Morning guys.


The single acting cylinder on my alignment hoist began to leak fluid out the cylinder vent about a week ago. It's of course been getting worse.
Yesterday my manager "fixed" it...

View attachment 319047 View attachment 319048 View attachment 319049

I'm hoping when the piston seals completely give up and it won't work at all a car is stuck on it with the ramps sitting on the locks just out of spite. Hopefully it's a used car. I actually would feel really bad if a customer had to go without because of this chit..
I'm to this point with a lot of *s-word here too. End of the day yesterday one of my fin formers started acting up after they hung a new coil of raw aluminum to feed it. Second screwed with it all night trying to get it to run and now it's back on my plate. I suggested trying some different raw material since that's when the problems started. Do you think they'd do it? *f-wordem the bastard can sit idle.

And good morning and stuff.
 
Last edited:

Mastermind

Chief Cat Herder
Staff member
Yearly GoldMember
Local time
10:37 AM
User ID
4
Joined
Dec 3, 2015
Messages
52,571
Reaction score
350,222
Location
Banner Springs Tennessee
Country flag
Morning guys.


The single acting cylinder on my alignment hoist began to leak fluid out the cylinder vent about a week ago. It's of course been getting worse.
Yesterday my manager "fixed" it...

View attachment 319047 View attachment 319048 View attachment 319049

I'm hoping when the piston seals completely give up and it won't work at all a car is stuck on it with the ramps sitting on the locks just out of spite. Hopefully it's a used car. I actually would feel really bad if a customer had to go without because of this chit..

The man is plainly an engineer. He deserves a raise.
 
Top